User manual AEG-ELECTROLUX EHG6760X

[. . . ] Gas hob - xc INSTRUCTION BOOKLET Mod. / Mîä. EHG 6760 35687-1802 CZ-HR-RO-RU-SK -SLO ENGLISH Important safety information These warnings are provided in the interest of safety. You MUST read them carefully before installing or using the appliance. About Installation, Cleaning and Manteinance · It is mandatory that all operations required for the installation are carried out by a qualified or competent person, in accordance with existing rules and regulations. Disconnect the appliance from the electrical supply, before carrying out any cleaning or manteinance work. [. . . ] Burner Big (rapid) Medium (semirapid) Small (auxiliary) minimum diameter 180 mm 120 mm 80 mm maximum diameter 260 mm 220 mm 160 mm 4 Maintenance and cleaning Disconnect the appliance from the electrical supply, before carrying out any cleaning or manteinance work. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. Wash the enamelled components with warm soapy water. Never use abrasive cleaners Frequently wash the "caps" and the "crowns" with hot soapy water, carefully taking away any built-up of food. Carefully wash the stainless steel components with water, then wipe them dry with a soft cloth. If the marks are particularly difficult to remove, use common non-abrasive cleaners or specific products. Never use steel wool pads or acids. Cast Iron Pan Supports The hob has cast iron pan supports. They are fair heavy and could damage the hob or your kitchen furniture if you let them fall down. To keep the pan supports in the correct position, they are hooked into hinges at the back of the hob. Thanks to these hooks, you can lift the pan supports for easier cleaning. When removing the pan supports, lift them up as shown in Fig. Never turn the pan supports on the hinges, this could damage them (Fig. This keeps the pan supports fixed in place when the central burner is in use. Wash the pan supports using hot soapy water. If necessary, a paste cleaner or a soap impregnated steel wool pad can be used with caution. After cleaning, be sure to wipe dry with a soft cloth. YES The Burners The burner caps and crowns (Fig. Wash the burner caps and crowns using hot soapy water, and remove marks with a mild paste cleaner. A well moistened soap impregnated steel wool pad can be used with caution, if the marks are particularly difficult to remove. After cleaning, be sure to wipe dry with a soft cloth. FO 2238 Fig. 2 NO Ignition electrode The electric ignition is obtained through a ceramic "electrode" and a metal electrode (Fig. Keep these components very clean, to avoid lighting difficulties, and check that the burner crown holes are not obstructed. Fig. 3 Periodic Maintenance Periodically ask your local Service Centre to check the conditions of the gas supply pipe and the pressure adjuster, if fitted. 5 Technical data Gas Burners Rating Rapid Burner (big) 3, 0 kW (G20 - 20 mbar) Semirapid Burner (medium) 2, 0 kW (G20 - 20 mbar) Auxiliary Burner (small) 1, 0 kW (G20 - 20 mbar) Class 3 Appliance Category II2H3+ Setting Natural Gas G20 - 20 mbar Gas connection Electric Supply G 1/2" 230 V 50 Hz Hob recess dimensions Length Width 560 mm 480 mm Instruction for the Installer " The following instructions about installation and maintenance must be carried out by qualified personnel in compliance with the regulation in force. [. . . ] Carry out the building in of the hob as follows: · put the relevant sealings, supplied with the hob, on the side edges of the cut out and at 8 mm from the front and rear edges, as shown in Fig. 10, taking care that the sealings meet without overlapping; place the hob in the cut out, taking care of its centring; fix the hob with the relevant screws (Fig. The traction of the screws is able to trace the sealing, any excess of which can then be easily removed. Fig. 10 · · The edge of the hob forms a double labyrinth seal which provides a total guarantee against infiltration of liquids. a a) sealing Fig. [. . . ]