User manual AEG-ELECTROLUX EHG6763X

[. . . ] Gas hob - Ankastre ocak INSTRUCTION INSTRUCTION BOOKLET MONTAJ KILAVUZU KULLANMA VE MONTAJ KILAVUZU Mod. EHG 6763 X 35688-3803 CZ-HR-RO-SI-SK-TR 2 Important Safety Information These warnings are provided in the interest of safety. You MUST read them carefully before installing or using the appliance. About Installation, Cleaning and Maintenance · It is mandatory that all operations required for the installation are carried out by a qualified or competent person, in accordance with existing rules and regulations. Disconnect the appliance from the electrical supply, before carrying out any cleaning or maintenance work. [. . . ] Burner minimum diameter 180 mm 120 mm 80 mm maximum diameter 260 mm 220 mm 160 mm Large (rapid) Medium (semirapid) Small (auxiliary) Fig. 2 5 Cleaning and Maintenance Disconnect the appliance from the electrical supply, before carrying out any cleaning or maintenance work. General cleaning Wash the enamelled components with warm soapy water. Never use abrasive cleaners Frequently wash the "caps" and the "crowns" with hot soapy water, carefully taking away any built-up of food. Regularly wipe over the hob top using a soft cloth weel wrung out in warm water to which a little liquid detergent has been added. Avoid the use of the following: - household detergent and bleaches; - impregnated pads unsuitable for non-stick saucepans; - steel wool pads; - bath/sink stain removers. Should the hob top become heavily soiled, it is recommended that a proper cleaning product is used. Fig. 3 FO 2110 Pan supports The pan supports are dishwasher proof. If the marks are particularly difficult to remove, use common non-abrasive cleaners or specific products. Never use steel wool pads or acids. The Burners The burner caps and crowns (Fig. Wash the burner caps and crowns using hot soapy water, and remove marks with a mild paste cleaner. A well moistened soap impregnated steel wool pad can be used with caution, if the marks are particularly difficult to remove. After cleaning, be sure to wipe dry with a soft cloth. Ignition candle The electric ignition is obtained through a ceramic "candle" and a metal electrode (fig. 1-lett. Keep these components well clean, to avoid difficult lighting, and check that the burner crown holes are not obstructed. Periodic Maintenance Periodically ask your local Service Centre to check the conditions of the gas supply pipe and the pressure adjuster, if fitted. To ensure the good operation of the hob and its safety features, it is necessary that the taps are periodically lubricated. The periodic lubrication of the taps must be carried out by qualified personnel, which you must refer to also in case of malfunctioning. 6 Instruction for the Installer The following instructions about installation and maintenance must be carried out by qualified personnel in compliance with the regulation in force. The side walls of the unit in which the hob is going to be installed, must not exceed the height of the working top. Avoid installing the appliance in the proximity of inflammable materials (e. g. The appliance must be electrically disconnected before all interventions. If any electric supply to the appliance is required to carry out the work, ensure all the necessary precautions are followed. THE MANUFACTURER WILL NOT ACCEPT LIABILITY, SHOULD ANY OF THE OTHER SAFETY INSTRUCTIONS INCORPORATED IN THIS BOOK OR THE REGULATION IN FORCE BE IGNORED. Technical Data Gas Burners Rating Rapid Burner 3, 0 kW (G20) - 2, 8 kW (G30/G31) Semirapid Burner 2, 0 kW Auxiliary Burner 1, 0 kW Appliance Class Category 3 II2H3B/P Natural Gas G20 - 20 mbar G 1/2" 230 V 50 Hz Setting Gas connection Electric Supply Length Width Hob recess dimensions 550 mm 470 mm 7 Gas connection Choose fixed connections or use a flexible pipe in stainless steel in compliance with the regulation in force. If using flexible metallic pipes, be careful they do not come in contact with mobile parts or they are not squeezed. Use the same attention when the hob is combinated with an oven. [. . . ] The edge of the cut out must have a minimum distance from the rear wall of 55 mm. If there are side walls, or sides of the furniture unit near the hob, the cut out edges must have a minimum distance of 100 mm. Hanging furniture units or hoods must be placed at 650 mm. R SR A = Rapid burner = Semirapid burner = Auxiliary burner 11 Fitting the hob to the worktop The hobs can be installed in a kitchen unit with an opening for insertion whose dimensions are shown in Fig. [. . . ]