User manual AEG-ELECTROLUX EHG7336X

[. . . ] Ensure a good ventilation around the appliance. A poor air supply could cause lack of oxygen. Ensure that the gas supply complies with the gas type stated on the identification label, placed near the gas supply pipe. Using a gas cooking appliance will produce heat and moisture in the room which it has been installed in. [. . . ] ABCDBurner cap Burner crown Ignition electrode Thermocouple triple crown burner · A B D C Fig. 1 · · 3 Using the hob correctly To ensure maximum burner efficiency, it is strongly recommended that you use only pots and pans with a bottom fitting the size of the burner used, so that flame will not spread beyond the bottom of the vessel (see the table beside). It is also advisable, as soon as a liquid starts boiling, to turn down the flame so that it will barely keep the liquid simmering. Carefully supervise cooking with fat or oil, since these types of foodstuff can result in a fire, if overheated. Burner Triple Crown (ultra rapid) Big (rapid) Medium (semirapid) Small (auxiliary) minimum diameter 180 mm 180 mm 120 mm 80 mm maximum diameter 260 mm 260 mm 220 mm 160 mm 4 Maintenance and Cleaning Disconnect the appliance from the electrical supply, before carrying out any cleaning or manteinance work. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. Wash the enamelled components with warm soapy water. Never use abrasive cleaners Frequently wash the "caps" and the "crowns" with hot soapy water, carefully taking away any built-up of food. Carefully wash the stainless steel components with water, then wipe them dry with a soft cloth. If the marks are particularly difficult to remove, use common non-abrasive cleaners or specific products. Never use steel wool pads or acids. Cast Iron Pan Supports The hob has cast iron pan supports. No. ) marked on the identification plate. Original spareparts, certified by the product manufacturer and carrying this symbol are only available at our Service Centre and authorized spareparts shops. Technical Data Gas Burners Rating Ultra Rapid Burner (Triple crown) 4, 0 kW Rapid Burner (big) 2, 8 kW Semirapid Burner (medium) 2, 0 kW Auxiliary Burner (small) 1, 0 kW Class 3 Appliance Category II2H3+ Setting Natural Gas G20 - 20 mbar Gas connection Electric Supply G 1/2" 230 V 50 Hz Hob recess dimensions Length Width 560 mm 480 mm 6 Instruction for the Installer " The following instructions about installation and maintenance must be carried out by qualified personnel in compliance with the regulation in force. The appliance must be electrically disconnected before all interventions. If any electric supply to the appliance is required to carry out the work, ensure all the necessary precautions are followed. The side walls of the unit in which the hob is going to be installed, must not exceed the height of the working top. Avoid installing the appliance in the proximity of inflammable materials (e. g. curtains, tea towels etc. ). Gas Connection Choose fixed connections or use a flexible pipe in stainless steel. If using flexible metallic pipes, be careful they do not come in contact with mobile parts or they are not squeezed. Use the same attention when the hob is combinated with an oven. " " " IMPORTANT - To ensure a correct operation, a saving of energy and the long-life of the appliance, the voltage pressure of the appliance must correspond to the recommended values. The adjustable connection is fixed to the comprehensive ramp by means of a threaded nut G 1/2". Interpose the sealing between the components as shown in Fig. [. . . ] The yellow/green earth wire must be approximately 2 cm longer than the phase wires (Fig. To open the terminal block and reach the terminals, proceed as follows: " Fig. 5 insert the point of a screwdriver into the visible protrunding part of the terminal block; exert a light pressure and lift (Fig. 6 " 8 Adaptation to different types of gas ! [. . . ]