User manual AEG-ELECTROLUX EHGT328CX

[. . . ] EHGT 328 35692-3302 MY-TH-SG English Important Safety Information These warnings are provided in the interest of safety. You MUST read them carefully before installing or using the appliance. About Installation, Cleaning and Maintenance · It is mandatory that all operations required for the installation are carried out by a qualified or competent person, in accordance with existing rules and regulations. Disconnect the appliance from the electrical supply, before carrying out any cleaning or maintenance work. Ensure a good ventilation around the appliance. [. . . ] Carefully supervise cookings with fats or oil, since these types of foodstuff can result in a fire, if overheated. A B D Fig. 1 Energy saving advices To ensure maximum burner efficiency, it is strongly recommended that you use only pots and pans with a bottom fitting the size of the burner used, so that flame will not spread beyond the bottom of the vessel (see the table beside). It is also advisable, as soon as a liquid starts boiling, to turn down the flame so that it will barely keep the liquid simmering. · Use only pans or pots with flat bottom. C Burner minimum diameter 180 mm. 160 mm. Rapid Auxiliary Cleaning and Maintenance Disconnect the appliance from the electrical supply, before carrying out any cleaning or manteinance work. Wash the enamelled components with warm soapy water. Never use abrasive cleaners Frequently wash the "caps" and the "crowns" with hot soapy water, carefully taking away any built-up of food. Carefully wash the stainless steel components with water, then wipe them dry with a soft cloth. If the marks are particularly difficult to remove, use common non-abrasive cleaners or specific products. In models provided with electric ignition, this feature is obtained through a ceramic "candle" and a metal electrode (Fig. Keep these components well clean, to avoid difficult lighting, and check that the burner crown holes (lett. B) are not obstructed. Periodic maintenance Periodically ask your local Service Centre to check the conditions of the gas supply pipe and the pressure adjuster, if fitted. To ensure the good operation of the hob and its safety features, it is necessary that the taps are periodically lubricated. The periodic lubrication of the taps must be carried out by qualified personnel, which you must refer to also in case of malfunctioning. 4 Guarantee - After Sales Service Original spare parts This appliance, before leaving the factory, has been tested and studied by many experts and specialists, in order to give you the best results. Any repair work which needs to be carried out should be done with the utmost care and attention. For this reason we reccomend that for any problem you contact the dealer who sold it to you, or our nearest authorized Service Centre, specifying the nature of the problem and the particular model which you own. Original spare parts, certified by the manufacturer of the product and marked with the following sign, can only be found at our approved Technical Assistance Centres and in authorised Spare Parts Shops. 5 Technical Data Gas Burners Rating Rapid Burner (big) Auxiliary Burner (small) Class 3 Appliance Setting Gas connection Electric Supply Length Width 2, 8 kW (G30/G31) 1, 0 kW Liquid Gas G30/G31 28-30 mbar G 1/2" 220 / 240 V ~ 50 / 60 Hz 270 mm. This appliance complies with the following Directives: 73/23 - 90/683 (Low Voltage Directive); 89/336 (Electromagnetical Compatibility Directive); 90/396 (Gas Appliances) 93/68 (General Directives) and subsequent modifications. Hob recess dimensions Instruction for the Installer · · The following instructions about installation and maintenance must be carried out by qualified personnel in compliance with the regulation in force. The side walls of the unit in which the hob is going to be installed, must not exceed the height of the working top. Avoid installing the appliance in the proximity of inflammable materials (e. g. The appliance must be electrically disconnected before all interventions. If any electric supply to the appliance is required to carry out the work, ensure all the necessary precautions are followed. THE MANUFACTURER WILL NOT ACCEPT LIABILITY, SHOULD ANY OF THE OTHER SAFETY INSTRUCTIONS INCORPORATED IN THIS BOOK OR THE REGULATION IN FORCE BE IGNORED. · · 6 Gas connection Choose fixed connections or use a flexible pipe in stainless steel in compliance with the regulation in force. [. . . ] Finally check the flame does not go out when quickly turning the knob from the maximum position to the minimum position. This procedure can easily be carried out, anyhow the hob has been positioned or built in the working top. Table 2 : injectors BURNER NORMAL POWER kW REDUCED POWER kW TOWN GAS inj. 1/100 Auxiliary (small) Town gas 1, 1 LPG : 1, 0 Rapid (big) Town gas 2, 9 LPG : 2, 8 0, 75 234 0, 55 86 203 200 0, 33 134 m3/h 0, 210 NORMAL POWER LPG G30/G31 28-30 mbar inj. [. . . ]