User manual AEG-ELECTROLUX EHM6722X

[. . . ] Gas hobs - Kombinirana plinska i plinsko-strujna plo ca - Vgradna kuhalna plosca INSTRUCTION BOOKLET UPUTE ZA UPOTREBU NAVODILA ZA UPORABO Mod. EHG 671 - EHM 6731 - EHM 6722 35679-4801 HR-RO-SI-SK-BG English Important Safety Information These warnings are provided in the interest of safety. You MUST read them carefully before installing or using the appliance. About Installation, Cleaning and Maintenance · It is mandatory that all operations required for the installation are carried out by a qualified or competent person, in accordance with existing rules and regulations. Disconnect the appliance from the electrical supply, before carrying out any cleaning or maintenance work. [. . . ] Never use abrasive cleaners Frequently wash the "caps" and the "crowns" with hot soapy water, carefully taking away any built-up of food. Regularly wipe over the hob top using a soft cloth weel wrung out in warm water to which a little liquid detergent has been added. Avoid the use of the following: - household detergent and bleaches; - impregnated pads unsuitable for non-stick saucepans; - steel wool pads; - bath/sink stain removers. Should the hob top become heavily soiled, it is recommended that a proper cleaning product is used. Fig. 3 FO 2110 Pan supports The pan supports are dishwasher proof. If the marks are particularly difficult to remove, use common non-abrasive cleaners or specific products. Never use steel wool pads or acids. Service and original spare parts This machine, before leaving the factory, has been tested and studied by many experts and specialists, in order to give you the best results. Any repair work which needs to be carried out should be done with the utmost care and attention. For this reason we recommend that for any problem you contact the dealer who sold it to you, or our nearest authorized Service Centre, specifying the nature of the problem, the appliance model (Mod. ), the product number (Prod. No. ) marked on the identification plate. Original spareparts, certified by the product manufacturer and carrying this symbol are only available at our Service Centre and authorized spareparts shops. Ignition candle The electric ignition is obtained through a ceramic "candle" and a metal electrode (fig. 1-lett. Keep these components well clean, to avoid difficult lighting, and check that the burner crown holes are not obstructed. Cleaning of the hotplates Spills on the hotplates should be removed using warm water and a soft cloth. Alternatively, wipe the plates with a drop of olive oil on a kitchen towel (while the plates are still warm). Periodic Maintenance Periodically ask your local Service Centre to check the conditions of the gas supply pipe and the pressure adjuster, if fitted. To ensure the good operation of the hob and its safety features, it is necessary that the taps are periodically lubricated. · The periodic lubrication of the taps must be carried out by qualified personnel, which you must refer to also in case of malfunctioning. 5 Technical Data Gas Burners Rating Rapid Burner 3, 0 kW (G20) - 2, 8 kW (G30/G31) Semirapid Burner 2, 0 kW Auxiliary Burner 1, 0 kW Appliance Class Category 3 II 2H3+ Natural Gas G20 - 20 mbar G 1/2" Setting Gas connection Electric hotplates Mod. EHM 6722 Small hotplate Large hotplate Ø 145 mm. 1500 W 1000 W 2000 W Electric Supply 230 V 50 Hz Hob recess dimensions Length Width 550 mm. 470 mm. Instruction for the Installer · · The following instructions about installation and maintenance must be carried out by qualified personnel in compliance with the regulation in force. The side walls of the unit in which the hob is going to be installed, must not exceed the height of the working top. Avoid installing the appliance in the proximity of inflammable materials (e. g. The appliance must be electrically disconnected before all interventions. If any electric supply to the appliance is required to carry out the work, ensure all the necessary precautions are followed. [. . . ] · Finally check the flame does not go out when quickly turning the knob from the maximum position to the minimum position. This procedure can easily be carried out, anyhow the hob has been positioned or built in the working top. Fig. 8 By-pass screws Table 1 : By-pass diameters Burner Ø By-pass in 1/100 of mm. 40 32 28 Rapid Semi-rapid Auxiliary Table 2 : injectors TYPE OF GAS TYPE OF BURNER INJECTORS MARKS 1/100 mm NOMINAL POWER INPUT KW 3, 0 2, 0 1, 0 2, 8 2, 0 1, 0 REDUCED POWER kW NOMINAL POWER 3 m /h 0, 286 0, 190 0, 095 g/h 202 144 72 NOMINAL PRESSURE mbar NATURAL GAS G 20 LPG (Buthane/ Propane) Rapid (large) Semi-rapid (medium) Auxiliary (small) Rapid (large) Semi-rapid (medium) Auxiliary (small) 119 96 70 86 71 50 0, 65 0, 45 0, 33 0, 65 0, 45 0, 33 20 28-30/37 9 Building In P R SR P P SR A 58 0 58 0 A 0 50 0 50 Mod. [. . . ]