User manual AEG-ELECTROLUX EHS620X

[. . . ] · Only let bigger children work on the appliance under supervision. · To avoid small children and pets unintentionally switching the appliance on, we recommend activation of the child safety device. General safety · The appliance may only be installed and connected by trained, registered service engineers. · Built-in appliances may only be used after they have built in to suitable built-in units and work surfaces that meet standards. · In the event of faults with the appliance or damage to the glass ceramic (cracks, scratches or splits), the appliance must be switched off and disconnected from the electrical supply, to prevent the possibility of an electric shock. [. . . ] Triple cooking zone To switch on middle ring To switch on outside ring To switch off outside ring To switch off middle ring Sensor panel Touch Touch Touch Touch for 1-2 seconds. for 1-2 seconds. Power indicator One power indicator is lit. First power indicator goes out. Roasting zone To switch on outside ring To switch off outside ring Sensor panel Touch seconds Touch seconds for 1-2 for 1-2 Power indicator is lit goes out Locking/unlocking the control panel The control panel, with the exception of the "On/Off" sensor field, can be locked at any time in order to prevent the settings being changed e. g. Control panel Switch on Switch off Touch Touch Display (for 5 seconds) previously set heat setting When you switch the appliance off, the locking function is automatically switched off. 12 electrolux operating the appliance Using the automatic warm-up function All cooking zones are equpped with an automatic warm up function When setting a heat setting using , when starting from , the cooking zone switches to full power for a certain amount of time and then automatically switches back to the heat setting set. Control panel Switch on (only when starting at ) Switch off Not used Touch possible heat Display settings to (after 5 seconds) Touch Touch to to / to to If during the automatic warm up a higher heat setting is selected, e. g. from to , the automatic warm up is adjusted. If there is still residual heat on the cooking zone (display ), the automatic warm up is not performed. operating the appliance electrolux 13 The length of time that the automatic warm up function operates depends on the heat setting selected. Heat setting v 1 2 3 4 5 6 7 8 9 Length of the automatic warm up [min:sec] 0:30 1:00 1:40 4:50 6:30 10:10 2:00 3:30 4:30 --- 14 electrolux operating the appliance Using the child safety device The child safety device prevents unintentional use of the appliance. Control panel Switch on the appliance (Do not set a heat setting) Touch Touch until the signal sounds Acoustic signal Display/Signal Appliance switches off. Overriding the child safety device The child safety device can be released in this way for a single cooking session; it remains activated afterwards. Touch Control panel Switch on the appliance and at the same time / acoustic signal Display/Signal Until the appliance is next switched off, it can used as normal. After overriding the child safety device, a heat setting or a function must be set within approx. 10 seconds, otherwise the appliance automatically switches itself off. operating the appliance electrolux 15 Releasing the child safety device Step 1. The bottom should be as thick and flat as possible. · Cookware made of enamelled steel or with aluminium or copper bottoms can leave discolorations on the glass ceramic surface which are difficult or impossible to remove. 20 electrolux tips on cooking and frying Energy saving Always place cookware on the cooking zone before it is switched on. If possible, always place lids on the pans. Switch cooking zones off before the end of the cooking time, to take advantage of residual heat. Bottom of pans and cooking zones should be the same size. tips on cooking and frying electrolux 21 Examples of cooking applications The information given in the following table is for guidance only. Switch the appliance on again Switch off the lock (See the section "Locking/unlocking the control panel") Remove objects. The lock is switched on Acoustic signal sounds when appliance is switched off The residual heat indicator is not displaying anything The control panel is wholly or partly covered by objects. The cooking zone was only on If the cooking zone is supfor a short time and is therefore posed to be hot, call the Cusnot hot tomer Service Department. Let the cooking zone cool down The automatic warm up func- There is still residual heat on tion is not switching itself on the cooking zone The highest heat setting is set The highest heat setting has the same power as the automatic warm up function The heat setting was set using 1. Switching off the cooking the sensor field zone 1. Set the cooking zone using the sensor field Acoustic signal sounds and The On/Off sensor field has appliance switches itself on been covered up, e. g. by a and then off again; after 5 sec- cloth onds another acoustic signal sounds is lit Do not place any objects on the control panel Overheating protection for the Switch off the cooking zone. cooking zone has been trigSwitch the cooking zone on gered again Safety cut-out has been triggered Switch off the cooking zone. Switch the cooking zone on again what to do if . . . electrolux 25 Problem and number are displayed Possible cause Electronics fault Remedy Disconnect the appliance from the electrical supply for a few minutes (Take the fuse out of the house's wiring system) If after switching on again, is displayed again, call the customer service department and minus are displayed Light rays that are too strong Briefly shade the control panel, on the control panel, for exam- for example with the hand ple bright sunlight Acoustic signal sounds, appliance switches itself off Switch appliance on (again) If you are unable to remedy the problem by following the above suggestions, please contact your dealer or the Customer Care Department. Warning!Repairs to the appliance are only to be carried out by qualified service engineers. [. . . ] Suitable isolation devices include line protecting cut-outs, fuses (screw type fuses are to be removed from the holder), earth leakage trips and contactors. Sticking on the seal · Clean the worktop around the cutout area. · Stick the single-sided adhesive sealing tape provided on the underside of the hob around the outside edge ensuring that it is not stretched. The two ends of the tape should join in the middle of one side. [. . . ]