User manual AEG-ELECTROLUX EHS8671P85C

[. . . ] Do not place or store flammable liquids, highly inflammable materials or fusible objects (e. g. plastic film, plastic, aluminium) on or near the appliance. Safety when cleaning For cleaning, the appliance must be switched off and cooled down. For safety reasons, the cleaning of the appliance with steam jet or high-pressure cleaning equipment is not permitted. How to avoid damage to the appliance The glass ceramic can be damaged by objects falling onto it. The edge of the glass ceramic can be damaged by being knocked by the cookware. [. . . ] First power indicator goes out. Double ring cooking zone To switch on outside ring To switch off outside ring Touch Touch Sensor field for 1-2 seconds for 1-2 seconds Pilot light is lit goes out Roasting zone To switch on outside ring To switch off outside ring Sensor panel Touch Touch for 1-2 seconds for 1-2 seconds Power indicator is lit goes out Locking/unlocking the control panel The control panel, with the exception of the "On/Off" sensor field, can be locked at any time in order to prevent the settings being changed e. g. Control panel Switch on Switch off Touch Touch Display l (for 5 seconds) previously set heat setting 3 When you switch the appliance off, the locking function is automatically switched off. 8 Using the automatic warm-up function All cooking zones are equpped with an automatic warm up function When setting a heat setting using , when starting from , the cooking zone switches to full power for a certain amount of time and then automatically switches back to the heat setting set. Control panel Switch on (only when starting at ) Switch off Not used Touch Touch Touch possible heat set- Display tings to to / u to u a (after 5 seconds) to u to u 3 If during the automatic warm up a a higher 3 If there is stillh), the automatic the cooking residual heat on warm up is zone (display not performed. heat setting is selected, e. g. from to , the automatic warm up is adjusted. The length of time that the automatic warm up function operates depends on the heat setting selected. Heat setting v 1 2 3 4 5 6 7 8 9 Length of the automatic warm Intermediate up [min:sec] heat setting 0:30 1:00 1:40 4:50 6:30 10:10 2:00 3:30 4:30 --2. 2:40 5:30 8:10 12:20 2:30 Length of the automatic warm up [min:sec] 9 Using the child safety device The child safety device prevents unintentional use of the appliance. Setting the child safety device Step 1. Control panel Switch on the appliance (Do not set a heat setting) Touch Touch until the signal sounds Display/Signal Acoustic signal l Appliance switches off. The child safety device is engaged. Releasing the child safety device Step 1. Control panel Switch on the appliance Touch Touch until the signal sounds Display/Signal l Acoustic signal Appliance switches off. The child safety device is released. Overriding the child safety device The child safety device can be released in this way for a single cooking session; it remains activated afterwards. Control panel Switch on the appliance Touch and at the same time Display/Signal l / acoustic signal Until the appliance is next switched off, it can used as normal. 10 Using the timer All cooking zones can use each use one of the two timer functions at the same time. Function Automatic cut-out Condition a heat setting is set Outcome after the time has elapsed acoustic signal 00 flashes Cooking zone switches off acoustic signal 00 flashes Countdown timer cooking zones not in use 3 If a cookingiszone switched off. Rub the appliance dry using a clean cloth. Remove Type of dirt sugar, food containing sugar plastics, tin foil limescale and water rings fat splashes shiny metallic discolorations immediately yes yes ------when the appliance has cooled down ----yes yes yes cleaner for glass ceramic or stainless steel* using a scraper* *Scrapers and cleaners for glass ceramic and stainless steel can be purchased in specialist shops 3 Remove stubborn residues with a cleaner for glass ceramic or stainless steel. 3 Scratches or dark stains on the glass ceramic that cannot be removed do not however affect the functioning of the appliance. 16 What to do if . . . Problem The cooking zones will not switch on or are not functioning Possible cause Remedy More than 10 seconds have passed Switch the appliance on again. since the appliance was switched on The child safety device is switched Deactivate the child safety device (See the section "Child safety deon l vice") Several sensor fields were touched Only touch one sensor field at the same time Safety cut-out has been triggered Remove any objects (pan, cloths, etc. ) that are lying on the control panel. Switch the appliance on again Switch off the lock (See the section "Locking/unlocking the control panel") The lock is switched on l Acoustic signal sounds when appli- The control panel is wholly or partly Remove objects. ance is switched off covered by objects. The residual heat indicator is not displaying anything The cooking zone was only on for a If the cooking zone is supposed to short time and is therefore not hot be hot, call the Customer Service Department. Let the cooking zone cool down The highest heat setting has the same power as the automatic warm up function 1. Switching off the cooking zone 2. Set the cooking zone using the sensor field Do not place any objects on the control panel The automatic warm up function is There is still residual heat on the not switching itself on cooking zone h The highest heat setting is set The heat setting was set using the sensor field Acoustic signal sounds and appli- The On/Off sensor field has been ance switches itself on and then off covered up, e. g. by a cloth again; after 5 seconds another acoustic signal sounds _ is lit Overheating protection for the cooking zone has been triggered Safety cut-out has been triggered Switch off the cooking zone. Switch the cooking zone on again Switch off the cooking zone. Switch the cooking zone on again Disconnect the appliance from the electrical supply for a few minutes (Take the fuse out of the house's wiring system) If after switching on again, e is displayed again, call the customer service department e and number are displayed Electronics fault e and minus are displayed Light rays that are too strong on the Briefly shade the control panel, for control panel, for example bright example with the hand Acoustic sunlight signal sounds, appliance switches itself off Switch appliance on (again) 17 If you are unable to remedy the problem by following the above suggestions, please contact your dealer or the Customer Care Department. 1 Warning!Repairs to the appliance are only to be carried out by qualified service engineers. 3 If the appliance has been wrongly operated, the visit from the customer service technician or dealer may not take place free of charge, even during the warranty period. Considerable danger to the user may result from improper repairs. Disposal 2 Packaging material The packaging materials are environmentally friendly and can be recycled. [. . . ] Loose and inappropriate plug and socket connections can make the terminal overheat. Have the clamping joints correctedly installed by a qualified electrician. In the event of single-phase or two-phase connection, the appropriate mains cable of type H05BB-F Tmax 90 (or higher) must be used. If this appliance's mains cable is damaged, it must be replaced by a special cable (type H05BB-F Tmax 90; or higher). [. . . ]