User manual AEG-ELECTROLUX EHS8680X 64A

[. . . ] plastic film, plastic, aluminium) on or near the appliance. How to avoid damage to the appliance The glass ceramic can be damaged by objects falling onto it. The edge of the glass ceramic can be damaged by being knocked by the cookware. Cookware made of cast iron, cast aluminium or with damaged bottoms can scratch the glass ceramic if pushed across the surface. Objects that melt and things that boil over can burn onto the glass ceramic and should be removed straightaway. [. . . ] from to , the automatic warm up is adjusted. The length of time that the automatic warm up function operates depends on the heat setting selected. Heat setting v 1 2 3 4 5 6 7 8 9 Length of the automatic warm up [min:sec] 0:30 1:00 1:40 4:50 6:30 10:10 2:00 3:30 4:30 --- 8 Using the child safety device The child safety device prevents unintentional use of the appliance. Setting the child safety device Step 1. Control panel Switch on the appliance (Do not set a heat setting) Touch Touch until the signal sounds Display/Signal Acoustic signal l Appliance switches off. The child safety device is engaged. Overriding the child safety device The child safety device can be released in this way for a single cooking session; it remains activated afterwards. Control panel Switch on the appliance Touch and at the same time Display/Signal l / acoustic signal Until the appliance is next switched off, it can used as normal. 3 After overriding the child safety device, a heat setting or a function must be set within approx. 10 seconds, otherwise the appliance automatically switches itself off. Releasing the child safety device Step 1. Control panel Switch on the appliance Touch Touch until the signal sounds Display/Signal l Acoustic signal Appliance switches off. The child safety device is released. 9 Using the timer Function Automatic cut-out Pre-requisite With heat setting set Result after time has elapsed Acoustic signal 00 flashes Cooking zone switches off Acoustic signal 00 flashes Countdown timer Cooking zones are not switched on 3 While the countdown timer is activated, no cooking zone can be used. 3 The countdown timer basically cannot be used if a cooking zone is switched on. 3 If a cooking zone is switched off, the timer function set is also switched off. Selecting a cooking zone Step 1. Touch Control panel once Display Pilot light of the first cooking zone flashes 2. Touch once Pilot light of the second cooking zone flashes 3. Touch once Pilot light of the third cooking zone flashes 4. Touch once Pilot light of the fourth cooking zone flashes 3 If the pilot light is flashing more slowly, the heat setting can be set or modified. by a damp cloth or with liquid Switch the appliance on again. Safety cut-out has been triggered The lock is switched on l Switch the appliance on again Switch off the lock (See the section "Locking/unlocking the control panel") The residual heat indicator is not displaying anything The cooking zone was only on for a If the cooking zone is supposed to short time and is therefore not hot be hot, call the Customer Service Department. Let the cooking zone cool down The highest heat setting has the same power as the automatic warm up function 1. Switching off the cooking zone 1. Set the cooking zone using the sensor field Do not place any objects on the control panel The automatic warm up function is There is still residual heat on the not switching itself on cooking zone h The highest heat setting is set The heat setting was set using the sensor field Acoustic signal sounds and appli- The On/Off sensor field has been ance switches itself on and then off covered up, e. g. by a cloth again; after 5 seconds another acoustic signal sounds _ is lit e and number are displayed Overheating protection for the cooking zone has been triggered Electronics fault Switch off the cooking zone. Switch the cooking zone on again Disconnect the appliance from the electrical supply for a few minutes (Take the fuse out of the house's wiring system) If after switching on again, e is displayed again, call the customer service department If you are unable to remedy the problem by following the above suggestions, please contact your dealer or the Customer Care Department. 1 Warning!Repairs to the appliance are only to 3 If the appliance has been wrongly technician operated, the visit from the customer service or dealer may not take place free of charge, even during the warranty period. 16 be carried out by qualified service engineers. Considerable danger to the user may result from improper repairs. Disposal 2 Packaging material The packaging materials are environmentally friendly and can be recycled. The plastic components are identified by markings, e. g. Please dispose of the packaging materials in the appropriate container at the community waste disposal facilities. 2 Old appliance The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. [. . . ] Loose and inappropriate plug and socket connections can make the terminal overheat. Have the clamping joints correctedly installed by a qualified electrician. In the event of single-phase or two-phase connection, the appropriate mains cable of type H05BB-F Tmax 90 (or higher) must be used. If this appliance's mains cable is damaged, it must be replaced by a special cable (type H05BB-F Tmax 90; or higher). [. . . ]