User manual AEG-ELECTROLUX EHT310X

[. . . ] 12 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 If the gas-hob does not work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Service and spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The damage is caused by transport at a later date, for instance during removal or resale. The damage is caused by any form of use contrary to common sense. product and serial numbers on receipt you will always have this information to hand (See frontpage). These numbers will be needed for any service visits. The model number plate is placed on the bottom of the hob. When the operating knob is released the gas ring goes out again? Saftey To enable the consumer to locate any leaks in the installation, a smelling substance has been added to all gas qualities available in the market - town gas, natural gas or bottled gas. When smelling gas or in case of any other kind of malfunction of the unit switch off the main gas supply or the bottled gas and contact service, an authorized heating and sanitary engineer or your gas supplier. It is recommended that a maintenance check of the gas installation and the unit should be performed at least every three years. Consult your authorized heating and sanitary engineer. The gas ring burns very unevenly?? Positioning It is advisable to place the unit near an out-of-the-way, or closed corner, with space on either side on which to rest hot cooking utensils. The unit should not be placed at a heavily-trafficked or open corner, nor in a passageway. Unpacking Check to see whether the unit is damaged. Distribution damages Any damages due to transportation by us or by our representative must be reported to the dealer not later than one week after receipt of the unit. Check If you make a note of the model, 20 5 Overview If the wok-hob does not work Check to see whether a fuse has blown. Check to see whether the relay is switched off. If the problem is not with the fuse or relay, do not attempt to correct it yourself. Instead, contact our service network all repairs must be performed by our service personnel. by an alternative service organisation, approved by the distributor. Only spare parts delivered by the distributor may be used. Spare parts and service are the domain of our service network. Burner Knob Warranty This unit is warranted against defects in materials and workmanship, when used as intended, for a period of one year from the date of purchase. The warranty covers both parts and service, as well as necessary transportation costs. Keep your proof of purchase. Placement of grid Reservations The warranty does not cover damages which are not due to defects in materials or workmanship. Repair, or attempted repair, by any party other than our authorized service network will invalidate the warranty. The warranty does not cover an unjustified house-call by our service network. Wrong Right Guide knob for grid Service and spare parts Service and repair of this unit must be carried out by our service personnel, or 6 19 Technical data Type of gas Adjusted to town gas: -8 mbar Category and pressures I1a - 8 mbar Max. nominal load Q, HS (Towngas): Wok burner = 3, 3 kW x 1 Total= 3, 3 kW FSD The unit features fully-secured gas taps (thermo-fuse). HS = Gross calorific value Q = Nominal load Voltage= Ignition transformer= 220-240 V AC 50 HZ - 0, 6 VA Operations Panel markings The operating knob has a ring showing the scale of markings. [. . . ] You must be able to hear a click telling you that the rings have been correctly fitted. 1 The operating panel with knob pan support top plate and burner covers/rings are to be cleaned with ordinary cleaning agents. However, do not use any kind of scouring powder. Air valve Fig. 1 The hob with the stainless steel top plate is to be washed with ordinary soap and water. [. . . ]