User manual AEG-ELECTROLUX EHT7127CX

[. . . ] We promise that it will provide a superior User Experience delivering Ease-ofMind. Good luck! 4 electrolux Contents Instructions for the User Important Safety Information Description of the Hob Operation Maintenance and Cleaning Something Not Working?Service and original spare parts 5 7 8 10 12 Instructions for the Installer Engineers Technical Data Gas Connection Electrical Connection Adaptation to different Types of Gas Building In Possibilities for Insertion 13 15 17 18 19 21 Guide to Use the instructions The following symbols will be found in the text to guide you throughout the Instructions: Safety Instructions !Step by step instructions for an operation Hints and Tips Environmental Information This appliance is manufactured according to the following EEC directives: 73/23 EEC - 90/683 EEC - 93/68 EEC 89/336 EEC - 90/396 EEC, current edition. electrolux 5 ENGLISH Important Safety Information These warnings are provided in the interest of safety. [. . . ] To light a burner: knob anticlockwise to turn the relevant " " maximum position and push down the knob to ignite. After lighting the flame, keep the knob pushed down for about 5 seconds. This will allow the "thermocouple" (Fig. D) to be heated and the safety device to be switched off, otherwise the gas supply would be interrupted. Then, check the flame is regular and adjust it as required. If you cannot light the flame even after several attempts, check the "cap" (Fig. To put the flame out, turn the knob to the symbol . A - Burner cap B - Burner crown C - Ignition electrode D - Thermocouple Fig. 1 In the absence of electricity, ignition can occur without the electrical device; in this case approach the burner with a flame, push the relevant knob down and turn it anti-clockwise until it reaches the"maximum" position. When switching on the mains, after installation or a power cut, it is quite normal for the spark generator to be activated automatically. electrolux 9 Using the hob correctly To ensure maximum burner efficiency, it is strongly recommended that you use only pots and pans with a flat bottom fitting the size of the burner used, so that flame will not spread beyond the bottom of the vessel (see the table beside). Burner Large (rapid) Medium (semi-rapid) Small (auxiliary) minimum diameter 160 mm 120 mm 80 mm maximum diameter 260 mm 220 mm 160 mm As soon as a liquid starts boiling, turn down the flame so that it will barely keep the liquid simmering. If you use a saucepan which is smaller than the recommended size, the flame will spread beyond the bottom of the vessel, causing the handle to overheat. Ensure any residues are wiped off before the cooking zones are used again. If scratches or cracks are noticed, disconnect the appliance from the electrical supply to avoid the risk of electric shock and call your nearest Service Force Centre. electrolux 11 Keep all objects and materials which can melt away from the cooking surface, e. g. Care should be taken when preparing food or drinks containing sugar. If anything of this nature accidentally comes into contact with the ceramic surface it must be scraped off immediately while stlll hot and wiped away to avoid damage to the surface. The burners The burner caps and crowns can be removed for cleaning. Wash the burners taps and crowns using hot soapy water, and remove marks with a mild paste cleaner. A well moistened soap impregnated steel wool pad can be used with caution, if the marks are particularly difficult to remove. After cleaning, be sure to wipe dry with a soft cloth. Ignition electrode The electric ignition is obtained through a ceramic "electrode" and a metal electrode (Fig. The appliance must be electrically disconnected before all interventions. If any electric supply to the appliance is required to carry out the work, ensure all the necessary precautions are followed. The side walls of the unit in which the hob is going to be installed, must not exceed the height of the working top. Avoid installing the appliance in the proximity of inflammable materials (e. g. curtains, tea towels etc. ). " " " THE MANUFACTURER WILL NOT ACCEPT LIABILITY, SHOULD ANY OF THE OTHER SAFETY INSTRUCTIONS INCORPORATED IN THIS BOOKLET OR THE REGULATION IN FORCE BE IGNORED. Gas Connection Choose fixed connections or use a flexible pipe instainless steel in compliance with the regulation in force. [. . . ] 6 · With a thin screwdriver, adjust the by-pass screw positioned in the centre of the gas tap control shaft (see Fig. If changing from natural gas 20 mbar Minimum adjustment screw to liquid gas, completely tighten the adjustment screw in. If changing from liquid gas to natural gas 20 mbar, undo the by-pass screw about 1/4 of a turn. If changing from natural gas 20 mbar to natural gas 13 mbar undo the by-pass screw about 1/4 of a turn. [. . . ]