User manual AEG-ELECTROLUX EKC6001

[. . . ] We promise that it'll make your life a little easier. Good luck! 2 Contents Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Changing plinth height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The coloured decor on the ceramic glass plate can become worn and scratched in time after it has been used. The heating zones The knobs for the heating zones are marked from 0 to 12, where 12 provides the highest heat. Do this if you want to use the front zones or the smaller rear one: 1 Turn clockwise to the desired position on the knob to the zone that you have chosen. 2 Zero the knob anti-clockwise after use. 18 Do this if you want to use the rear right-hand large heating zone: 1 Turn the knob clockwise past the symbol after the figure 12, 2 then turn the knob back to the desired position between 12 and 1. Zero the knob anti-clockwaise after use. You must experiment to find the setting and the heating zone that suits you and your pans, depending on the food that you are preparing. Here is a little guidance (to find the right heating setting): Choice of pan/frying pan A cooker with a ceramic glass plate makes greater demands on your pots and pans that a cooker with heating plates. Remember the following: · Check the bottom of the pans. Pans with a convex bottom (bulging outwards) tend to swivel on the ceramic glass plate and provide poor heating contact. · Aluminium has good heat conductivity, but can leave silvery marks on the plate. · Casseroles and pans that are made of glass or are enamelled with deep patterns cause more wear if they are pulled backwards and forwards on the plate than pots and pans made of other materials. 19 In order to save both time and energy the bottom of a pan or frying-pan · must cover the zone completely. But if the bottom is too small, then boilover can easily stick to the plate. When cooking is finished, turn the oven and temperature selectors back to zero. · · · · Countdown This function has no effect on the operation of the oven. "0. 00" flashes in the display. 0. 00 2. Within 5 seconds set the desired countdown using the + or - buttons (max. After 5 seconds the display shows the time remaining. 0. 30 23 When the time has elapsed, "0. 00" is displayed and an audible signal sounds for 2 minutes. The signal can be stopped by pressing any button. 0. 00 Meat probe Important: Only the meat probe supplied with the oven may be used. If replacing, please use only original replacement parts. Push the tip of the meat probe right into the meat so that the tip is in the centre of the meat. Insert the meat probe plug into the socket on the side wall of the oven as far as it will go. 3. Using the + or - button set the desired core temperature. 65 C The display changes to the current core temperature. The core temperature is displayed from 30°C. Set oven function and oven temperature. 30 C 24 As soon as the core temperature set is reached, an audible signal sounds. 65 C 5. [. . . ] After cleaning, place the drawer rollers on the brackets (SEE ILLUSTRATION). Lift it up slightly first of all, so that the wheels do not get caught in the front catch. 40 Technical data With reservations for possible changes. This equipment meets the demands in EC directives 89/336/EEC and 73/23/EEC. EKC60154 Width (mm): Height when delivered (mm): Depth: ENERGY EFFICIENCY CLASS ENERGY CONSUMPTION Conventional heating (kWh): Hot air (kWh): COOKING TIMES STANDARD LOAD Conventional heating (min): Hot air (min): 597 900 595 A 0. 89 0. 79 43 38 41 European Guarantee This equipment is covered by an Electrolux Guarantee in all the countries listed below during the period covered by the Guarantee or the laws of the country concerned. If you move from one of these countries to another of the countries listed below, the Guarantee follows the equipment under the following conditions: · The Guarantee covering the equipment starts to apply with effect from the day when it was purchased as shown by the valid purchase document issued by the sales company. [. . . ]