User manual AEG-ELECTROLUX EOG601X

[. . . ] Gas built-in oven INSTRUCTION BOOKLET Please read this instruction booklet before using the appliance Models EOG 601 35688-4401 GB Important Safety Information You MUST read these warnings carefully before installing or using the oven. If you need assistance, contact our Customer Care Department on 08705 950950 Installation · This appliance must be installed and serviced by a competent person as stated in the Gas Safety (Installation and Use) Regulations Current Editions and the IEE Wiring Regulations. For appliances installed in the Republic of Ireland please refer to NSAI-Domestic Gas Installations I. S. 813 Current Editions and the ETCI Rules for Electrical Installations. Remove all packaging, both inside and outside the oven, before using the oven. [. . . ] The shelf supports can be removed for easy cleaning. Undo the fixing nut which keep the shelf support in place. When carrying out this operation, keep the shelf support in position with the other hand. Then, disengage the rear hook and take off the shelf support. Please, ensure the retaining nuts are secure when refitting the shelf support. Models in stainless steel or aluminium We recommend to clean the oven door using only a wet sponge and dry it after cleaning with a soft cloth. Never use steel wool, acids or abrasive products as they can damage the oven surface. Clean the oven control panel following the same precautions. 1 2 10 Replacing the Oven Light Disconnect the appliance. If the oven bulb needs replacing, it must comply with the following specifications: - Wattage power: 15W, - Voltage: 230V (50 Hz), - Resistant to temperatures of 300°C, - Connection type: E14. These bulbs are available from your local Service Force Centre. Ensure the oven is disconnected from the electrical supply. Remove the faulty bulb and replace with the new one. Reconnect to the electrical supply. Something Not Working If the appliance is not working correctly, please carry out the following checks, before contacting your local Service Force Centre. IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is under guarantee. SYMPTOM The gas oven does not light nor the electric grill SOLUTION Check that the oven is switched on at the wall Check that the power supply has not been interrupted before the cooling fan has had time to cool the oven down Check that there is not a problem with your gas supply Check that you are using the recommended temperature settings and shelf positions. Check that the oven is installed properly. Check that you are using the recommended temperature settings and shelf positions. Check the light bulb, and replace it if necessary (see "Replacing the Oven Light") Refer to the contents of this booklet, especially to the chapter "Using the Gas Oven". Leave dishes inside the oven no longer than 15-20 minutes after the cooking is completed. In-guarantee customers should ensure that the above checks have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown. The gas oven does not light. Food is cooking too quickly or too slowly The oven is not cooking evenly The oven light does not work Steam and condensation settle on the food and the oven cavity. If after all these checks, your hob still does not operate correctly, contact your local Electrolux Service Force Centre. Please note that it will be necessary to provide proof of purchase for any in-guarantee service calls. 11 Service and Spare Parts In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your local Electrolux Service Force Centre by telephoning: 0870 5 929929 Your telephone call will be automatically routed to the Service Force Centre covering your post code area. For the address of your local Service Force Centre and further information about Service Force, please visit the website at www. serviceforce. co. uk Before calling out an engineer, please ensure you have read the details under the heading "Something Not Working. " When you contact the Service Force Centre you will need to give the following details: 1. [. . . ] gas supply ramp control panel A) View from above flexible metallic pipe(*) gasket gas supply ramp control panel (*) For mainland Europe only B) View from above nut rigid metallic pipe olive male/female adapter gas supply ramp View from above nut control panel 17 Conversion from Natural to LPG Gas IMPORTANT The replacement/conversion from Natural to LPG should only be undertaken by a competent and qualified engineer. It is important to note that this model is designed for use with natural gas but can be converted for use with LPG providing the correct injectors are fitted. The gas rate is adjusted to suit. Replacement of gas oven burner injector To replace the gas burner oven injector, follow this procedure: 1. Remove the bottom plate of the oven ("A") to access the gas oven burner; 2. [. . . ]