User manual AEG-ELECTROLUX ER1637T

[. . . ] Repairs carried out by inexperienced persons may cause injury or more serious malfunctioning. Refer to your local Service Centre, and always insist on genuine spare parts. s s Use s Care must be taken to ensure that the appliance does not stand on the electrical supply cable. There are working parts in this product which heat up. Always ensure that there is adequate ventilation as a failure to do this will result in component failure and possible food loss. [. . . ] Frozen food must not be re-frozen once it has been thawed out. Manufacturers' storage recommendations should be strictly adhered to. The inner lining of the appliance consists of channels through which the refrigerant passes. If these should be punctured this would damage the appliance beyond repair and cause food loss. DO NOT USE SHARP INSTRUMENTS to scrape off frost or ice. Frost may be removed by using the scraper provided. Under no circumstances should 9 Environment Protection s s This appliance does not contain gasses which could damage the ozone layer, in either its refrigerant circuit or insulation materials. The appliance shall not be discarded together with the urban refuse and rubbish. Avoid damaging the cooling unit, especially at the rear near the heat exchanger. Information on your local disposal sites may be obtained from your municipal authorities. The materials used on this appliance marked with the symbol are recyclable. DESCRIPTION OF THE APPLIANCE Butter shelf Shelf Bottle shelf Vegetable drawer Shelves Thermostat Defrosting water tray Ice-cube production compartment USE Cleaning the interior Before using the appliance for the first time, wash the interior and all internal accessories with lukewarm water and some neutral soap so as to remove the typical smell of a brand-new product, then dry thoroughly. 12 D731 SOMETHING NOT WORKING If the appliance is not functioning properly, check that: the plug is firmly in the wall socket and the mains power switch is on; there is an electricity supply (find out by plugging in another appliance); the thermostat knob is in the correct position. Also check the following: If the appliance is very noisy, check that the sides are not vibrating against adjacent kitchen units and that the refrigeration unit pipes are not vibrating. If your appliance is still not working properly after making the above checks, contact the nearest service centre. To obtain fast service, it is essential that when you apply for it you specify the model and serial number of your appliance which can be found on the guarantee certificate or on the rating plate located inside the appliance, on the bottom lefthand side. TECHNICAL SPECIFICATIONS The technical data is indicated in the rating plate on the left side inside the appliance. Height Width Depth 850 495 600 mm mm mm 13 INSTALLATION lf this appliance featuring magnetic door seals is to replace an older appliance having a spring lock (latch) on the door or lid, be sure to make that spring lock unusable before you discard the old appliance. This will prevent it from becoming a death-trap for a child. This appliance complies with the following E. E. C. Directives: - 73/23 EEC of 19. 2. 73 (Low Voltage Directive) and subsequent modifications; - 89/336 EEC of 3. 5. 89 (Electromagnetic Compatibility Directive) and subsequent modifications. Positioning The appliance should be installed well away from sources of heat such as radiators, boilers, direct sunlight etc. Best performance is obtained with ambient temperature between +18°C and +43°C (class T); +18°C and +38°C (class ST); +16°C and +32°C (class N); +10°C and +32°C (class SN). The class of your appliance is shown on its rating plate. For safety reasons, minimum ventilation must be as shown in Fig. : Appliance positioned under overhanging kitchen wall units (see Fig. -A). [. . . ] Two adjustable feet at the cabinet base allow accurate levelling of the appliance. 100 mm A 10 mm B 10 mm NP008 Door reversibility Before carrying out the operations described below, pull out the mains plug from the wall socket. Proceed as follows: Electrical connection Before plugging in, ensure that the voltage and frequency shown on the serial number plate correspond to your domestic power supply. Voltage can vary by +6% of the rated voltage. For operation with different voltages, a suitably sized autotransformer must be used. [. . . ]