User manual AEG-ELECTROLUX ER2007F

[. . . ] This appliance should be serviced by an authorized Service Centre, and only genuine spare parts should be used. It is dangerous to alter the specifications or modify this appliance in any way. Care must be taken to ensure that the appliance does not stand on the electrical supply cable. The domestic refrigerators and freezers are designed to be used specifically for the storage of edible foodstuffs only. [. . . ] This appliance does not contain gasses which could damage the ozone layer, in either its refrigerant circuit or insulation materials. The appliance shall not be discarded together with the urban refuse and rubbish. Avoid damaging the cooling unit, especially at the rear near the heat exchanger. Information on your local disposal sites may be obtained from your municipal authorities. Take utmost care when handling your appliance so as not to cause any damages to the cooling unit with consequent possible fluid leakages. The appliance must not be located close to radiators or gas cookers. Avoid prolonged exposure of the appliance to direct sunlight. There must be adequate ventilation round the back of the appliance and any damage to the refrigerant circuit must be avoided. For freezers only (except built-in models): an ideal location is the cellar or basement. 31 INSTALLATION If this appliance featuring magnetic door seals is to replace an older appliance having a spring lock (latch) on the door or lid, be sure to make that spring lock unusable before you discard the old appliance. This will prevent it from becoming a death-trap for a child. Instructions for totally built-in appliances Dimensions of the recess Model ER 1933 I Height Depth Width 1030 mm 550 mm 560 mm Model ER 2336 I 1225 mm 550 mm 560 mm Positioning The appliance should be installed well away from sources of heat such as radiators, boilers, direct sunlight etc. ; best performance is obtained with ambient temperature between +16°C and +32°C (class N) or between +10°C and +32°C (class SN). The class of your appliance is shown on its rating plate. 6 Remove the little plates and make the holes with a diam. Replace the little plates over the runners and screw in the screws provided (3. 5x16 mm). For the alignment of the kitchen unit PR35 door, if necessary, use the clearance size of the slotted holes. At the end of the procedure, check that the doors of the appliance and the kitchen unit open properly. Apply covers (B) on joint cover lugs and into hinge holes. Inner door reversal Using a screwdriver release bracket (1) by pressing on the internal spring (Fig. 10) and withdraw it from its seat together with the door; remove plug (2) and fit it in the hole left open on the opposite side; Fig. 7 H 20m m D094 Position the runners (H) at the top and bottom of the inside of the kitchen unit as shown in Fig. 7 and mark the position of the external holes. After preparing the holes, screw the runners to the kitchen unit door using 3. 5x16 mm screws. t u rn t h e d o o r through 180°, remove the bracket (1) and refit it on the 180° opposite side. Refit the door and 2 insert the top pin and bottom bracket 1 (1), pushing it into place. To ensure correct PR140 storage of food, the door is fitted with a simple spring device which holds it in the open position until it is properly closed. 33 USE Operation Insert the plug into the wall socket. Open the refrigerator door and turn the thermostat knob, clockwise, beyond the «O» (STOP) position. [. . . ] Important If there is a power failure when food is in the freezer, do not open the door of the freezer compartment. 14 D037 PR151 when defrosting is completed, dry the interior thoroughly and refit the plug; keep the scraper for future use; turn the thermostat knob back to the required setting or replace the plug in the power socket. After two or three hours, reload the previously removed food into the compartment. Important: A temperature rise of the frozen food packs, during defrosting, may shorten their safe storage life. 36 MAINTENANCE Unplug the appliance before carrying out any maintenance operation. [. . . ]