User manual AEG-ELECTROLUX ER2835I

[. . . ] INFO INSTALLATIONS- UND GEBRAUCHSANWEISUNG I N S T R U C T I O N S P O U R L' I N S T A L L A T I O N E T L' E M P L O I INSTALLATION AND INSTRUCTION MANUAL I S T R U Z I O N I P E R L' I N S T A L L A Z I O N E E L'USO KÜHLSCHRANK REFRIGERATEUR REFRIGERATOR FRIGORIFERO ER 2835 I ER 2835 I ER 2835 I ER 2835 I 2222 014-71 This document was created with FrameMaker 4. 0. 4 CONTENTS Warnings . . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page 21 22 22 22 22 22 22 25 25 25 25 25 26 26 26 26 27 28 28 28 28 28 Installation . Positioning . Electrical connection . Cleaning the interior . Building-in instructions . [. . . ] Directives: - 73/23 EEC of 19. 2. 73 (Low Voltage Directive) and subsequent modifications; - 89/336 EEC of 3. 5. 89 (Electromagnetic Compatibility Directive) and subsequent modifications. Positioning The appliance should be installed well away from sources of heat such as radiators, boilers, direct sunlight etc. Best performance is obtained with ambient temperature between +18°C and +43°C (class T); +18°C and +38°C (class ST); +16°C and +32°C (class N); +10°C and +32°C (class SN). The class of your appliance is shown on its rating plate. For building into kitchen units follow the special "Building-in" instructions given. Cleaning the interior Before using the appliance for the first time, wash the interior and all internal accessories with lukewarm water and some neutral soap so as to remove the typical smell of a brand-new product, then dry thoroughly. Do not use detergents or abrasive powders, as these will damage the finish. Electrical connection Before plugging in, ensure that the voltage and frequency shown on the serial number plate correspond to your domestic power supply. Voltage can vary by ±6% of the rated voltage. For operation with different voltages, a suitably sized auto-transformer must be used. Building-in instructions Door reversibility (Fig. 1) P P A P1 D564 P1 Fig. 1 Right opening Remove the pins (P) and (P1). Left opening Remove (P) from both sides and the door. Remove (A) and refit it on the opposite side. Refit the door and (P) on the left side. Remove (P1) from the right side. 22 Recess dimensions Height Depth Width 1580 mm 550 mm 560 mm Fig. 5 For safety reasons, minimum ventilation must be as shown in Fig. Attention: keep ventilation openings clear of obstruction. 50-min. 2 D288 C Open the door and push the appliance against the side of the kitchen unit opposite to that of appliance hinges. Fasten the appliance with 4 screws provided in the kit included with the appliance. Snap vent grille (C) and hinge cover (D) into position. Fig. cm2 200 Press in the joint covers between the appliance and the kitchen unit. D033 Fig. 3 A Push appliance into housing until stop strip (A) touches the kitchen unit. D030 Fig. 7 Apply covers (B) on joint cover lugs and into hinge holes. D015 Fig. 4 A D265 If after having carried out the previously described operation there is still some space left between the appliance and the kitchen unit, fit the trimming provided together with the appliance on the stop strip (A). B D353 23 Fig. 11 H 20m m D094 Position the runners (H) at the top and bottom of the inside of the kitchen unit as shown in Fig. [. . . ] Do not use metallic instruments to remove the trays from the freezer. 26 Defrosting Frost is automatically eliminated from the evaporator of the refrigerator compartment every time the motor compressor stops, during normal use. The defrost water drains out through a trough into a special container at the back of the appliance, over the motor compressor, where it evaporates. It is important to periodically clean the defrost water drain hole in the middle of the refrigerator compartment channel to prevent the water overflowing and dripping onto the food inside. Use the special cleaner provided, which you will find already inserted into the drain hole. Fig. [. . . ]