User manual AEG-ELECTROLUX ER3136I

[. . . ] INFO I N S T R U C C I O N E S PA R A L A I N S TA L A C I O N Y E L U S O INSTALLATION AND INSTRUCTION MANUAL FRIGORIFICO-CONGELADOR FRIDGE-FREEZER ER 3136 I ER 3136 I 2222 240-24 This document was created with FrameMaker 4. 0. 4 CONTENTS Warnings . . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page 12 13 13 13 13 13 13 14 15 15 16 16 16 16 17 17 17 17 18 18 19 19 19 19 19 Installation . . Power connection . Cleaning the appliance's interior . . Installation of the appliance in a fitted kitchen unit . Instructions to assemble the refrigerator door to the kitchen unit door . [. . . ] This appliance complies with the following E. E. C. Directives: - 73/23 EEC of 19. 2. 73 (Low Voltage Directive) and subsequent modifications; - 89/336 EEC of 3. 5. 89 (Electromagnetic Compatibility Directive) and subsequent modifications. Building in Recess dimensions Height 1780 mm Depth 550 mm Width 560 mm To ensure adequate ventilation, allow the clearances shown in Fig. 2 Cleaning the appliance's interior Before using the appliance for the first time, wash all internal parts with lukewarm water and neutral soap so as to remove the typical «new» smell and then dry thoroughly. Do not use detergents or abrasive powders as these will damage the finish. min. cm 2 200 D027 13 Installation of the appliance in a fitted kitchen unit (Fig. 3) Drill the unit using a Ø 2. 5 mm drill (10 mm max. penetration); Fix the square fitting (1) to the appliance and apply the rubber seal; If the door is not already assembled fix the square fitting (2) to the refrigerator and fitting (3) to the unit column. Fit the refrigerator into the space recessing it by 48 mm in relation to the unit base (Fig. 4); Fix the refrigerator with the screws (5) to the upper and lower part of the unit, after having inserted the fittings (6) under the lower hinges; Fix the square fitting (1) to the unit column and the square fittings (2-3) to each other, after inserting the clip (4). 3 18mm 4 3 2 13mm 5 1 fl 2, 5 5 6 D612 Fig. 4 48mm 14 Instructions to assemble the refrigerator door to the kitchen unit door Position the runners (C) at the top and bottom of the inside of the kitchen unit as shown in Fig. 5 and mark the position of the external holes. After preparing the holes, screw the runners to the kitchen unit door using 3. 5x16 mm screws. Fig. 5 Remove the little plates and make the holes with a diam. Replace the little plates over the runners and screw in the screws provided (3. 5x16 mm). For the alignment of the kitchen unit door, if necessary, use the clearance size of the slotted holes. At the end of the procedure, check that the doors of the appliance and the kitchen unit open properly. Fig. 7 C 20m m D416 D135 Open both the appliance door and that of the kitchen unit to approx. Place the little plates over the runners. Hold the doors of the appliance and the unit together and mark the holes. Fig. 6 Reversibility of the freezer door (Fig. 8) When changing the hinges of the refrigerator door from right to left, it is also advisable to change the opening side of the freezer door. [. . . ] The formation of a thin layer of frost (as for example on the front edge of the freezer) does not require complete defrosting. Eliminate this layer periodically using a plastic scraper (do not use knives or sharp objects). If a thick layer has formed it will be necessary to carry out a complete defrosting as follows: 1. Take out all the frozen food and wrap it in newspapers placing it in a container (basin or paper box, etc. ) in a cool place until the cleaning operations have been completed. [. . . ]