User manual AEG-ELECTROLUX ER6334U

[. . . ] refrigerator INSTRUCTION MANUAL ER 6334 U 2222 682-63 UK CONTENTS Instructions for the User Important Safety Instructions Description of the Appliance Operation Before use Setting the temperature Fresh food refrigeration The door shelves The -star compartment Freezing fresh food Frozen food storage Thawing Making ice cubes Normal Operating Sounds Instructions for the Installer 3 4 5 5 5 5 5 6 6 6 6 6 6 Technical Specifications Installation Positioning 13 13 13 Electrical Connection Building-in Instructions Inner door reversal Grid preparation Door reversal Building the appliance in under a worktop Fitting the plinth 15 16 16 16 17 18 21 Health and Safety Guidelines Defrosting Maintenance and Cleaning Internal cleaning Periodic cleaning Changing the light bulb When the appliance is not in use 7 8 9 9 9 9 9 Something Not Working?Service and Spare Parts Customer Care Department Guarantee Conditions 10 11 11 12 2 IMPORTANT SAFETY INSTRUCTIONS These warnings are provided in the interests of your safety. Ensure that you understand them all before installing or using this appliance. If you are unsure about any of the meanings of these warnings contact the Customer Care Department. Prior to Installation s General Safety s Check the appliance for transport damage. [. . . ] Use the special cleaner provided (P) which you will find already inserted into the discharge hole The freezer compartment, however, will become progressively covered with frost. This should be removed with the special plastic scraper provided, whenever the thickness of the frost exceeds 4 mm. During this operation it is not necessary to switch off the power supply or to remove the foodstuffs. Never use sharp metal tools to scrape off frost from the evaporator as you could damage it. Do not use a mechanical device or any artificial means to speed up the thawing process other than those recommended by the manufacturer. However, when the ice becomes very thick on the inner liner, complete defrosting should be carried out as follows: 1. pull out the plug from the wall socket or turn the thermostat knob to the «O» setting; 2. remove any stored food, wrap it in several layers of newspaper and put it in a cool place; 3. leave the door open, place a basin on the top shelf of the refrigerator compartment, under the drain hole, remove the plug as shown in the figure; 4. when defrosting is completed, dry the interior thoroughly and refit the plug. Keep the scraper for future use; turn the thermostat knob back to the required setting or replace the plug in the power socket. After two or three hours, reload the previously removed food into the compartment. Important A temperature rise of the frozen food packs, during defrosting, may shorten their safe storage life. P F S. I. 011 PR151 8 MAINTENANCE AND CLEANING Before any maintenance or cleaning work is carried out, DISCONNECT the appliance from the ELECTRICITY supply. Warning This appliance contains hydrocarbons in its cooling unit maintenance and recharging must therefore only be carried out by authorised technicians. Changing the light bulb Should the interior light fail to work, first switch off the appliance and disconnect from the electricity supply, then replace the bulb as follows: Internal cleaning Clean the inside and accessories with warm water and bicarbonate of soda (5ml to 0. 5 litre of water). NEVER USE DETERGENTS, ABRASIVE POWDERS, HIGHLY PERFUMED CLEANING PRODUCTS OR WAX POLISHES, TO CLEAN THE INTERIOR AS THESE WILL DAMAGE THE SURFACE AND LEAVE A STRONG SMELL. Clean the drain hole of the water trough at regular intervals and make sure that the drain hole is never obstructed, so that the defrost water may flow freely. Important Do not use abrasive products. D411 1. Unscrew the light cover and then pull it outward by pressing as shown in the figure. Unscrew the bulb and replace it with a new 15 watt bulb (available from your nearest local Service Force centre). Replace the light cover by sliding it into its original position and replacing the screw. Periodic cleaning The appliance is equipped with a ventilation grid. Keep clean to guarantee good ventilation and good working order of the appliance. An accumulation of dust will affect the performance of the appliance and cause excessive electricity consumption. [. . . ] Refit the door and insert the top pin and bottom bracket (1), pushing it into place. To ensure correct storage of food, the door is fitted with a simple spring device which holds it in the open position until it is properly closed. 180° 2 1 PR140 Before carrying out any work, remove the plug from the power socket. Grid preparation Left door opening: Remove the left side (A) of the grid cutting it from the rear (see figure). A B Right door opening: Remove the right side (B) of the grid cutting it from the rear (see figure). DO002/2 To position the grid on the appliance proceed as follows: Apply the grid to the base of the appliance by pushing on to the clasps (a) until they click. a a DO001 15 Door reversal To reverse the opening direction of the door, proceed as shown in the figures: 6 4 1 7 8 5 2 3 1 2 10 13 9 12 11 3 Attention After completion of the door reversing operation, check that the door gasket adheres to the cabinet. If the ambient temperature is cold (i. e. in Winter), the gasket may not fit perfectly to the cabinet. [. . . ]