User manual AEG-ELECTROLUX ER7336I

[. . . ] I N FO INSTALLATION UND GEBRAUCHSANWEISUNGEN INSTRUCTIONS POUR L'INSTALLATION ET L'EMPLOI INSTALLATIE - EN GEBRUIKSAANWIJZINGEN INSTALLATION AND INSTRUCTION MANUAL KÜHLSCHRÄNKE REFRIGERATEURS KOELKASTEN REFRIGERATORS KJØLESKAP ER 6933 I - ER 7336 I ER 6933 I - ER 7336 I ER 6933 I - ER 7336 I ER 6933 I - ER 7336 I ER 6933 I - ER 7336 I 2222 292-33 WARNINGS GB It is most important that this instruction book should be retained with the appliance for future reference. Should the appliance be sold or transferred to another owner, or should you move house and leave the appliance, always ensure that the book is supplied with the appliance in order that the new owner can be acquainted with the functioning of the appliance and the relevant warnings. These warnings are provided in the interest of safety. You must read them carefully before installing or using the appliance. s General Safety s This appliance should be serviced by an authorized Service Centre, and only genuine spare parts should be used. [. . . ] For safety reasons, minimum ventilation must be as shown in Fig. Attention: keep ventilation openings clear of obstruction. D567 min. 2 A Push appliance into the housing until stop strip (A) touches the kitchen unit. D022 If after having carried out the previously described operation there is still some space left between the appliance and the kitchen unit, fit the trimming provided together with the appliance on the stop strip (A). Fig. 3 A D265 Open the door and push the appliance against the side of the kitchen unit opposite to that of appliance hinges. Fasten the appliance with 4 screws provided in the kit included with the appliance. Snap vent grille (C) and hinge cover (D) into position. D Fig. 4 C D727 40 Press in the joint covers between the appliance and the kitchen unit. Fig. 5 D724 Apply covers (B) on joint cover lugs and into hinge holes. Fig. 6 B D726 Position the runners (H) at the top and bottom of the inside of the kitchen unit as shown in Fig. 7 and mark the position of the external holes. After preparing the holes, screw the runners to the kitchen unit door using 3. 5x16 mm screws. Fig. 7 A 20m m PR33 Open both the appliance door and that of the kitchen unit to approx. Place the little plates over the runners. Hold the doors of the appliance and the unit together and mark the holes. Fig. 8 8mm PR34 Remove the little plates and make the holes with a diam. Replace the little platee over the runners and screw in the screws provided (3. 5x16 mm). For the alignment of the kitchen unit door, if necessary, use the clearance size of the slotted holes. At the end of the procedure, check that the doors of the appliance and the kitchen unit open properly. Fig. 9 PR35 41 Inner door reversal Using a screwdriver release bracket (1) by pressing on the internal spring (Fig. 10) and withdraw it from its seat together with the door; remove plug (2) and fit it in the hole left open on the opposite side; turn the door through 180°, remove the bracket (1) and refit it on the opposite side. Refit the door and insert the top pin and bottom bracket (1), pushing it into place. To ensure correct storage of food, the door is fitted with a simple spring device which holds it in the open position until it is properly closed. 180° Fig. [. . . ] 13 Ice-cube production This appliance is equipped with one or more trays for the production of ice-cubes. Fill these trays with water, then put them in the freezer compartment. Do not use metallic instruments to remove the trays from the freezer. 44 Defrosting Frost is automatically eliminated from the evaporator of the refrigerator compartment every time the motor compressor stops, during normal use. [. . . ]