User manual AEG-ELECTROLUX ER7707B

[. . . ] Installation Instructions Dual Fuel Ranges E30DF74EPS E36DF76EPS E48DF76EPS 5995447082 2 Safety IMPORTANT SAFETY INSTRUCTIONS Safety Precautions Do not attempt to install or operate your unit until you have read the safety precautions in this manual. Safety items throughout this manual are labeled with a Warning or Caution based on the risk type. Definitions This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. WARNING WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. CAUTION CA UTION CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. CAUTION CA UTION CAUTION used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may result in property damage. IMPORT IMPOR TANT Indicates installation, operation or maintenance information which is important but not hazard related. Safety SAFETY PRECAUTIONS WARNING · · Read all instructions before using the appliance. [. . . ] If there is any doubt as to whether the power supply is properly polarized or grounded, have it checked by a qualified electrician. Preparing for Installation GAS AND ELECTRICAL ROUGH-IN Locations NOTE NO TE The shaded areas shown in the illustrations, denote the location of the gas stub and the electrical junction box/receptacle. For replacement purposes, the location of the existing utilities may be utilized provided that they do not interfere with the sides or rear of the range. If installing the gas valve behind the range, verify that local building codes will permit this. A manual shut valve must be installed in the gas piping, external to the appliance, for the purpose of turning on or shutting off gas to the appliance. Plan the location of the range and the gas supply to allow access to the valve when the unit is installed. Access to the remote circuit breaker panel/fuse box, with the range in place, must also be allowed for in the installation. Any openings in the wall behind the appliance and in the floor under the appliance must be sealed. Both the gas supply piping and shut-off valve, and the electrical junction box/ receptacle must be located so they do not interfere with the range when it is installed. In addition, the junction box must be located so the range can be removed for service when the conduit supplied with the unit is attached to the junction box. Do not lengthen the conduit or wiring provided with the range. All dimensions shown are based on standard American cabinets 36 inches (914mm) high at the finished countertop by 24 inches (610mm) deep, with a 25 inch (635mm) overall countertop depth. When installing the range into nonstandard cabinets, minimum clearances shown in the diagrams on page 11 must be maintained. Carefully check the location where the range is to be installed. For best performance, the range should be placed away from drafts that may be caused by doors, windows and HVAC outlets. 9 10 Preparing for Installation CABINET AND COUNTERTOP PREPARATION NO TES NOTES · If cabinet storage space is to be provided directly above the range, the risk of personal injury may be reduced by installing a ventilating hood that projects horizontally a minimum of 5 inches beyond the face of the cabinets. The range may be installed flush to the rear wall. We recommend installing a non-concombustible material on the rear wall above the range and up to the vent hood. It is not necessary to install non-combustible materials behind the range below the countertop height. The minimum distance from the sides of the range above the countertop to combustible side walls must be at least 10 inches. The E36DF76EPS and E48DF76EPS ranges are delivered with a 3" backguard from the factory. 9" and 24" backguards are available as options. The E30DF74EPS range is delivered with a 6" backguard from the factory. 9" and 12" backguards are available as options. [. . . ] To convert the range for LP gas, see the instructions supplied in the LP conversion package. Installation INSTALLING THE RANGE Measure from the floor to the countertop and adjust the leveling legs as required to position the top frame at the desired height, based on the cabinet and countertop installation. Carefully slide the range into position in the cutout. The rear anti-tip leg should engage the anti-tip bracket. 23 INSTALLING THE BURNER COMPONENTS Remove the brass burner rings, porcelain burner caps, and porcelain gates from their shipping packages. Place each burner ring onto its corresponding burner base, being certain that the four alignment tabs slide into the matching notches in the base. [. . . ]