User manual AEG-ELECTROLUX ER9199BSAN

[. . . ] F r i d g e -- f r e e z e r / J ä ä -- p a k a s t i n k a a p p i / K y l -- f r y s s k å p NL INSTRUCTION BOOK KÄYTTÖOHJE BRUKSANVISNING ER9198BSAN, ER9199BCRE GB FI 818 33 95--01/4 SE Safety instructions GB Your new fridge/freezer may have other functions compared to your previous one. Carefully read these instructions to learn how the appliance works and how to care for it. It will come in handy if you later sell the cabinet or give it to somebody else. These warnings are provided in the interests of your safety. [. . . ] Clean out the drip channel inside the fridge at regular intervals and ensure that the drip channel is clear at all times. If blocked carefully clear using a piece of flexible curtain wire inserted into the drain outlet to remove the blockage. External Cleaning Wash the outer cabinet with warm soapy water. Remove the ventilation grille (see the section "Removing the ventilation grille") and vacuum-clean under the cabinet. Once or twice a year dust the condenser (black grille) and the compressor at the back of the appliance, with a brush or vacuum cleaner, as an accumulation of dust will affect the performance of the appliance and cause excessive electricity consumption. When moving the cabinet, lift it by the front edge to avoid scratching the floor. To change the light bulb The light is switched on automatically when the door is opened. Before replacing the light bulb, disconnect the power plug from the outlet. Fold the grille backward by unsnapping the front edge. Use a bulb of the same type, E14 socket, maximum rating of 25 W. When replacing the light bulb, use a bulb of the same type as the original one. The glass must measure at least 18 mm in diameter at the socket. This will ensure close fitting of the bulb against the rubber seal in the socket. Defrosting the fridge The fridge is defrosted automatically every time the compressor stops. Frost formation can be prevented by: · not putting warm foodstuff inside the cabinet. · avoiding frequently opening the door or keeping it open too long. · do not place foodstuffs directly against the cold cooling plate. Electrolux 818 33 95-01/4 9 Defrosting the freezer A certain amount of frost will always form on the freezer shelves and around the top compartment. Defrost the freezer when the frost layer reaches a thickness of about 3-5 mm. Remove the freezer drawers and place them on top of each other by turning every other drawer one half turn. Put insulating material around the drawers, e. g. The frozen products can also be packed closely together and be kept in a cold location, e. g. Defrosting can be accelerated by placing bowls with hot water (not boiling) inside the freezer. Take out the drain spout and place it in the bottom freezer drawer where water can collect. Loosen the ventilation grille to enable the bowl to fit under the drain spout. [. . . ] Cabinet is placed at a location whose ambient temperature corresponds to the climate classification*, for which the appliance is designed. * See on the rating plate on the inside of the appliance. The following table shows which ambient temperature is correct for each climate classification. Climate classification SN N ST T for an ambient temperature of +10°C to +32°C +16°C to +32°C +18°C to +38°C +18°C to +43°C Model ER9199BCRE a) b) 50mm Check that the drain hose at the rear of the cabinet discharges into the drip tray. Model ER9198BSAN If the cabinet is placed in a corner and the side with the hinges facing the wall, the distance between the wall and the cabinet must be at least 10 mm to allow the door to open enough so that the shelves can be removed. If the cabinet is placed in a corner and the side with the hinges facing the wall, the distance between the wall and the cabinet must be at least 220 mm to allow the door to open enough so that the shelves can be removed. The power plug must be accessible after installation of the cabinet. Electrolux 818 33 95-01/4 14 Door Reversal 1. [. . . ]