User manual AEG-ELECTROLUX ERC3023

[. . . ] frigorifico / fridge / frigorífico MANUAL DE INSTRUÇÕES LIBRO DE INSTRUCCIONES INSTRUCTION BOOK ERC 3023 E P 2223 384-71 GB Distanciadores posteriores En la bolsita de la documentacion hay dos distanciadores que deberàn ser montados como se muestra en la figura. Aflojar los tornillos, introducir el distanciador debajo de la cabeza del tronillo y volver a atornillar. Rear spacers In the bag with the documentation, there are two spacers which must be fitted in the two top corners. Slacken the screws and insert the spacer under the screw head, then re-tighten the screws. Reversibilidad de la puerta Desconecte el enchufe antes de efectuar cualquier tipo de operación. Para cambiar la dirección de apertura de la puerta, proceda de la manera siguiente: 1. [. . . ] Directives: - 87/308 EEC of 2/6/87 relative to radio interference suppression. - 73/23 EEC of 19. 2. 73 (Low Voltage Directive) and subsequent modifications; - 89/336 EEC of 3. 5. 89 (Electromagnetic Compatibility Directive) and subsequent modifications. It must be possible to disconnect the appliance from the mains power supply; the plug must therefore be easily accessible after installation · · · · Use · The domestic refrigerators and freezers are designed to be used specifically for the storage of edible foodstuffs only. Best performance is obtained with ambient temperature between +18°C and +43°C (class T); +18°C and +38°C (class ST); +16°C and +32°C (class N); +10°C and +32°C (class SN). The class of your appliance is shown on its rating plate. Warning: when the ambient temperature is not included within the range indicated for the class of this appliance, the following instructions must be observed: when the ambient temperature drops below the minimum level, the storage temperature in the freezer compartment cannot be guaranteed; therefore it is advisable to use the food stored as soon as possible. · · Frozen food must not be re-frozen once it has been thawed out. Manufacturers' storage recommendations should be strictly adhered to. The inner lining of the appliance consists of channels through which the refrigerant passes. If these should be punctured this would damage the appliance beyond repair and cause food loss. DO NOT USE SHARP INSTRUMENTS to scrape off frost or ice. Frost may be removed by using the scraper provided. Under no circumstances should solid ice be forced off the liner. Solid ice should be allowed to thaw when defrosting the appliance. Do not place carbonated or fizzy drinks in the freezer as it creates pressure on the container, which may cause it to explode, resulting in damage to the appliance. 11 · · · · · · Service/Repair A · Shelf holders Your appliance is equipped with shelf retainers that make it possible to secure the shelves during transportation. To remove them proceed as follows: Move the shelf holders in the direction of the arrow, raise the shelf from the rear and push it forward until it is freed and remove the retainers. 18 C Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person This product should be serviced by an authorized Service Centre, and only genuine spare parts should be used. Under no circumstances should you attempt to repair the appliance yourself. Repairs carried out by inexperienced persons may cause injury or more serious malfunctioning. Refer to your local · · B · Installation · During normal operation, the condenser and compressor at the back of the appliance heat up considerably. For safety reasons, minimum ventilation must be as shown in the instructions. Attention: keep ventilation openings clear of obstruction. · Care must be taken to ensure that the appliance does not stand on the electrical supply cable. Important: if the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent. [. . . ] To set a colder temperature, press button (D). The indicator display the newly selected temperature for a few seconds and then shows again the inside compartment temperature. The newly selected-temperature must be reached after 24 hours. During the stability period by the first starting the temperature displayed can not correspond to the setting temperature. [. . . ]