User manual AEG-ELECTROLUX ESF 6248W

[. . . ] D i s h w a s h e r User information ESF 6248 822 612 737-00-230605-01 g Dear Customer, Please read these user instructions carefully and keep them to refer to later. Please pass the user instructions on to any future owner of the appliance. The following symbols are used in the text: 1 Safety instructions 3 Useful tips and hints 2 Environmental information Warning!Information that affects your personal safety. Information that prevents damage to the appliance. 2 Contents Operating Instructions . [. . . ] 3) When using this cycle the degree of water clouding determines the amount of soiling on the dishes. The length of the cycle and water and energy consumption can vary greatly ­ depending upon the load and how dirty the dishes are. Depending upon the soiling, the temperature of the water will be automatically adjusted to between 50°C and 65°C. 4) When using this cycle, only load the dishwasher half full. 5) Test programme for Test Institutes 18 14 2x 13 - 15 9 4) 12 - 24 1 to 2x 22 - 24 2x Water (litres) Main wash Final rinse Drying Selecting a programme When your dishes look like this, select: an intensive programme. a normal or energy-saving programme. a short programme (e. g. 30 minute programme). 19 Starting a dishwashing cycle 1. Check that the spray arms can turn freely. The remaining time expected for the cycle will be shown in the multi-display. The selected cycle will begin after approximately 3 seconds. Setting the Delay Timer a dishwashing cycle for between 1 and 19 hours. 1. Press the Delay Timer button repeatedly until the multi-display shows the desired time delay, for example 12h, if the cycle is to start in 12 hours. The Delay Timer indicator is illuminated. 3. The time remaining to the start of the cycle is continuously displayed (e. 1h etc. ). 3 With the delay timer you can delay the start of 3 During the dishwashing cycle, may be adjustthe remaining time shown in the multi-display ed according to the size of the load, degree of soiling, etc. To change the time delay: As long as the cycle has not yet started, you can still change the setting by pressing the DELAY TIMER button. Cancelling the time delay: Press the Delay Timer button repeatedly until the length of the selected cycle appears in the multi-display. The selected dishwashing cycle will begin immediately. Interrupting or aborting a dishwashing cycle Only interrupt a dishwashing cycle that is in progress if it is absolutely necessary. To change a dishwashing cycle As long as the cycle has not yet started, you can still change the dishwashing cycle. First abort the dishwashing cycle, then re-set the time delay, lastly select the new dishwashing cycle. Interrupting the dishwashing programme by opening the dishwasher door 1 Hot steam may aescape scalding. the door is when opened. The cycle will continue. Switching off the dishwasher Do not switch off the dishwasher until the multi-display indicates "0" for the remaining cycle time. 2. Turn off the water tap. Aborting the dishwashing cycle 1. Press function buttons 2 and 3 and keep them pressed. The programme display for the current cycle will flash for several seconds and then go out. The dishwashing cycle has been cancelled. If you want to start a new cycle, check whether there is any detergent in the dispenser. 1 Carefully open the door. Hot steam may escape. 3 Turning off the dishwasher will only interrupt a selected dishwashing cycle, not cancel it. [. . . ] (Make sure that the tap is not dripping. ) restricted by the use of the dishwasher, we recommend installing an additional tap, or fitting a T-branch to the existing tap. If you need a longer water inlet hose than that supplied, the following VDE-approved complete hose sets are to be used. These are available from your local dealer. ­ Hose kit "WRflex 100" (Code: 911 239 034) ­ Hose kit "WRflex 200" (Code: 911 239 035) 1 The water inlet hose must not be kinked, 3 So that access to the tap in the kitchen is not 31 Water drainage Drain hose entangled. [. . . ]