User manual AEG-ELECTROLUX ESF6510LJX

[. . . ] (See "Maintenance and cleaning" - Instruction book part 1) 8. Start the programme Depress the On/Off push button. The On/Off indicator light will come on and the machine will start. If you wish to interrupt the washing programme at any time press this button again. 2. [. . . ] Check that there is rinse aid and salt (See "Instruction book" - part 1) 3. Load the dishes Remove any scraps of food. Pull the lower basket out and arrange the saucepans, plates and cutlery in it. Pull the upper basket out and arrange the plates, saucers, glasses and cups etc. Slide the baskets back into the machine. 9. At the end of the washing programme At the end of the programme the dishwasher will automatically stop. The On/Off indicator light remains on until the On/Off push button is depressed. 10. Switch off the dishwasher Switch off the dishwasher by pressing the On/Off push button. Open the door and wait a few minutes before removing the dishes; in this way they will be cooler and the drying will be improved. Empty the lower basket first and then the upper one; this will avoid water dripping from the upper basket onto the dishes in the lower one. When the washing programme has finished, it is recommended that the dishwasher is unplugged and the water tap turned off. If the handles protrude from the bottom of the basket, obstructing the lower spray arm, load the cutlery with the handles facing upwards. Mix spoons with other cutlery to prevent them from sticking together. Silver cutlery tends to go black if mixed with steel cutlery. Place it in the cutlery basket separate from the others. For best results we recommend to use the cutlery grid provided (if the size and the dimensions of the cutlery allow it). If washing very large plates (over 27 cm and up to 32 cm in diameter) you can load them in the lower basket after moving the upper basket to the higher position. To move to the higher position proceed as follows: 1. Move the front runner stops (A) of the upper basket outward and slide the basket out. Refit the basket in the higher position and replace the stops (A) in their original position. RC01 A When the top basket is in the higher position it will only take plates up to 20 cm in diameter and you will not be able to use the cup racks. After loading your machine always close the door, as an open door can be a hazard. 9 Hints for test centres Before starting any test it is necessary to fill completely with salt the salt container and with rinse aid the rinse aid dispenser. Test standard: Reference programme: Load: Rinse aid selector: Detergent dosage: EN 50242 Bio 50°C 12 standard place settings position 5 25 g in the dispenser 5 g on the dispenser lid Arrangement upper basket Arrangement lower basket Arrangement cutlery basket Technical specifications Dimensions Width Height with worktop Height without worktop Max depth Max depth with open door Voltage 60 cm 85 cm 82 cm 63. 5 cm 115. 2 cm 230 V - 50 Hz 200 W 2100 W 2300 W 50 kPa (0. 5 bar) 800 kPa (8 bar) max. 60°C 12 place settings 10 Electrical connection Motor rating during wash Power of heating element Overall power Water supply pressure Water supply connection Capacity Minimum Maximum Water cold/hot Fitting under a counter (kitchen worktop or sink) By removing the machine's worktop, you can install it under a close fitting sink unit or a pre-existing top, providing the dimensions of the recess correspond to those shown in the picture. 570 - 600 600 IN05 Proceed as follows: - Remove the machine's worktop by unscrewing the two rear retaining screws, pull from the front and slide out the rear slots, lifting the worktop. Insert the machine after adjusting height and levelling with the adjustable feet. [. . . ] 60°C 12 place settings 10 Electrical connection Motor rating during wash Power of heating element Overall power Water supply pressure Water supply connection Capacity Minimum Maximum Water cold/hot Fitting under a counter (kitchen worktop or sink) By removing the machine's worktop, you can install it under a close fitting sink unit or a pre-existing top, providing the dimensions of the recess correspond to those shown in the picture. 570 - 600 600 IN05 Proceed as follows: - Remove the machine's worktop by unscrewing the two rear retaining screws, pull from the front and slide out the rear slots, lifting the worktop. Insert the machine after adjusting height and levelling with the adjustable feet. When inserting the machine, ensure that the water inlet and drain hoses are not kinked or squashed. Levelling Good levelling is essential for correct closure and sealing of the door. When the appliance is correctly levelled, the door will not catch on the levelling spacers on either side of the cabinet. [. . . ]