User manual AEG-ELECTROLUX ESF66085WR

[. . . ] Should the appliance be sold or transferred to another owner, or should you move house and leave the appliance, always ensure that the book is left with the appliance in order that the new owner can get to know the functioning of the appliance and the relevant safety information. This information has been provided in the interest of your safety. You MUST read it carefully before installing or using the appliance. Installation q Check your dishwasher for any transport damage. If your dishwasher is damaged, you should contact your supplier. [. . . ] Never fill the rinse aid dispenser with any other substances (e. g. dishwasher cleaning agent, liquid detergent). Press simultaneously function push buttons 2 and 3, until the indicator lights of the function push buttons 1, 2 and 3 start flashing. Press the function push button 2, the indicator lights of function push buttons 1 and 3 turn off while the indicator light of the function push button 2 goes on flashing, at the same time the indicator light End of programme illuminates indicating that the inflow of rinse aid is active. To deactivate the inflow of rinse aid, press the function push button 2 again, the indicator light End of programme turns off, indicating that the inflow of rinse aid has been deactivated. To memorise the operation, switch off the dishwasher by pressing the On/Off push button or wait about 60 seconds after which the dishwasher will automatically return to setting mode. To activate the inflow of rinse aid follow the above instructions until the indicator light End of programme illuminates. Adjusting the dose According to the finish and drying results obtained, adjust the dose of rinse aid by means of the 6 position selector (position 1 minimum dosage, position 6 maximum dosage). Increase the dose if there are drops of water or lime spots on the dishes after washing. Reduce it if there are sticky whitish streaks on the dishes or a bluish film on glassware or knife blades. BR09 Top up the rinse aid when the indicator light on the control panel illuminates. 26 In daily use q q q q Check if it's necessary to refill with special salt or rinse aid Load cutlery and dishes into the dishwasher. Select a wash programme suitable for the cutlery and dishes. Start the wash programme. Loading cutlery and dishes Sponges, household cloths and any object that can absorb water may not be washed in the dishwasher. q q Before loading the dishes, you should: - Remove large left-overs. When the basket is in the higher position you will not be able to use the cup rack(s). The upper basket The upper basket is designed for plates (dessert plates, saucers, dinner plates of up to 24 cm in diameter), salad bowls, cups and glasses. Arrange items on and underneath the cup racks so that water can reach all surfaces. Glasses with long stems can be placed upside down in the cup racks. US47 For taller items, the cup racks can be folded upwards. Light items (plastic bowls etc. ) must be loaded in the upper basket and arranged so they do not move. RC01 After loading your machine always close the door, as an open door can be a hazard. US73 In case that plates are loaded in the upper basket: load them starting from the rear positions of the basket; tilting them slightly forwards and avoiding the front positions near the door. US71 Before closing the door, ensure that the spray arms can rotate freely. 28 Use of detergent Only use detergents specifically designed for use in dishwashers. Using no more then the correct amount of detergent contributes to reducing pollution. Prior to the start of a wash programme (not for the "Rinse and Hold" programme). The detergent is released during the washing phase. Please observe the manufacturer's dosing and storage recommendations as stated on the detergent packaging. Fill with detergent 1. If the lid is closed: press release button (1). Fill the detergent dispenser (2) with detergent. [. . . ] Check the water drain hose connection. Protection against flooding is active. Close the water tap and contact the Service Force Centre. Once the checks have been carried out, close the door and press the push button of the programme that was running before the intervention of the alarm, the programme will continue from the point in which it was interrupted. If the fault code reappears contact the Service Force Centre. For other combinations of fault codes not described in the above chart will appear, please contact your Service Force Centre. . . . there are problems when operating the dishwasher Fault Possible cause The dishwasher door has not been properly closed. The programme does not start The fuse has blown in the household fuse box. [. . . ]