User manual AEG-ELECTROLUX ESI6230W

[. . . ] D i s h w a s h e r User information ESI 6230 822 612 774-00-130705-01 g Dear customer, Please read this User Information carefully and keep it to refer to at a later date. Pass this User Information on to any subsequent owner of the appliance. The following symbols are used in the text: 1 Safety instructions 3 Useful tips and hints 2 Environmental information Warning: Notes that concern your personal safety. Attention: Notes that show how to avoid damage to the appliance. 2 Contents Operating Instructions . Adjusting the height of the upper basket . [. . . ] 3) When using this cycle, only load the dishwasher half full. 4) Test programme for Test Institutes 20 14 2x 14 - 16 9 3) 22 - 24 Water (litres) Main wash Final rinse Drying Selecting a programme When your dishes look like this, select: an intensive programme. a normal or energy-saving programme. a short programme (e. g. 30 minute programme). 21 Starting a dishwashing cycle 1. Check that the spray arms can turn freely. The remaining time expected for the cycle will be shown in the multi-display. The selected cycle will begin after approximately 3 seconds. Setting the Delay Timer a dishwashing cycle for between 1 and 19 hours. 1. Press the Delay Timer button repeatedly until the multi-display shows the desired time delay, for example 12h, if the cycle is to start in 12 hours. The Delay Timer indicator is illuminated. 3. The time remaining to the start of the cycle is continuously displayed (e. 1h etc. ). 3 With the delay timer you can delay the start of 3 During the dishwashing cycle, may be adjustthe remaining time shown in the multi-display ed according to the size of the load, degree of soiling, etc. To change the time delay: As long as the cycle has not yet started, you can still change the setting by pressing the DELAY TIMER button. Cancelling the time delay: Press the Delay Timer button repeatedly until the length of the selected cycle appears in the multi-display. The selected dishwashing cycle will begin immediately. Interrupting or aborting a dishwashing cycle Only interrupt a dishwashing cycle that is in progress if it is absolutely necessary. To change a dishwashing cycle As long as the cycle has not yet started, you can still change the dishwashing cycle. First abort the dishwashing cycle, then re-set the time delay, lastly select the new dishwashing cycle. Interrupting the dishwashing programme by opening the dishwasher door 1 Hot steam may aescape scalding. the door is when opened. The cycle will continue. Switching off the dishwasher Do not switch off the dishwasher until the multi-display indicates "0" for the remaining cycle time. 2. Turn off the water tap. Aborting the dishwashing cycle 1. Press function buttons 2 and 3 and keep them pressed. The programme display for the current cycle will flash for several seconds and then go out. The dishwashing cycle has been cancelled. If you want to start a new cycle, check whether there is any detergent in the dispenser. 1 Carefully open the door. Hot steam may escape. 3 Turning off the dishwasher will only interrupt a selected dishwashing cycle, not cancel it. The cycle will recommence after turning the dishwasher back on again. · Hot dishes are sensitive to knocks. Therefore leave the dishes to cool for about 15 minutes before removing them. · Dishes dry more quickly if you open the door for a moment after the cycle has ended and then leave it slightly open. Removing the dishes 3 It is to be damp. the inner door and the dispensnormal for ers · Empty the lower basket first, then the upper basket. [. . . ] · The drain hose must be fixed to the sink outlet connection using the hose clamp supplied. Anti-flood system For protection from water damage, the dishwasher is equipped with a anti-flood system. In the event of a fault, the safety valve in the water inlet hose immediately interrupts the supply of water to the appliance and the drain pump is activated. In this way water can neither escape nor overflow. The remaining water in the appliance is automatically pumped out. Electrical connection Details about the voltage, type of supply and the fuses required are to be found on the rating plate. [. . . ]