User manual AEG-ELECTROLUX ESI662-K

[. . . ] Adjusting the Height of the Upper Basket . Selecting the dishwashing cycle (Cycle Table) . If the Dishwashing Results are not Satisfactory . 4 4 5 5 7 7 9 10 12 12 15 16 17 18 20 20 20 21 23 23 25 26 26 27 28 28 29 30 32 34 35 Installation and connection instructions. [. . . ] 4) When using this cycle, only load the dishwasher half full. 5) Test programme for Test Institutes 6) This cycle does not need any detergent. 18 4 13 - 15 9 4) 12 - 24 1 to 2x 22 - 24 2x Water (litres) Main wash Final rinse Drying Selecting a programme When your dishes look like this, select: an intensive programme. a normal or energy-saving programme. a short programme (e. g. 30 minute programme). 19 Starting a Dishwashing Cycle 1. Check that the spray arms can turn freely. The remaining time expected for the cycle will be shown in the multi-display. The selected cycle will begin after approximately 3 seconds. Setting the Delay Timer a dishwashing cycle for between 1 and 19 hours. 1. Press the Delay Timer button repeatedly until the multi-display shows the desired time delay, for example 12h, if the cycle is to start in 12 hours. The Delay Timer indicator is illuminated. 3. The time remaining to the start of the cycle is continuously displayed (e. 1h etc. ). 3 With the delay timer you can delay the start of 3 During the dishwashing cycle, may be adjustthe remaining time shown in the multi-display ed according to the size of the load, degree of soiling, etc. To change the time delay: As long as the cycle has not yet started, you can still change the setting by pressing the DELAY TIMER button. Cancelling the time delay: Press the Delay Timer button repeatedly until the length of the selected cycle appears in the multi-display. The selected dishwashing cycle will begin immediately. Interrupting or Cancelling a dishwashing cycle Interrupt a dishwashing cycle that is in progress if it is absolutely necessary. To change a dishwashing cycle As long as the cycle has not yet started, you can still change the dishwashing cycle. When cleaning is necessary, remove spray arm from the fixture and clean jets with a pointed object (wire or needle). Then rinse out the spray arm using a strong jet of water. 3 Do not damage the jet opening. Upper basket spray arm 1. To remove upper basket spray arm, tilt it down hard. Place cleaned upper basket spray arm back in position against the connecting piece: press the two together firmly, until you feel them snap into place. 22 Bottom spray arm 1. To remove bottom spray arm, pull it upwards out of its catch. Place bottom spray arm back in position against connecting piece and press down firmly, until you feel it snap into place. What to do if. . . Remedying small malfunctions If one of the following fault codes is displayed in the multi-display during operation: ­ Fault codeÅ 10 (Problems with water inlet), ­ Fault codeÅ 20 (Problems with water drainage), please have a look at the following table. When the fault is remedied, press the button for the cycle that has started. With other fault codes ("Å " followed by a number): ­ Abort the dishwashing cycle. ­ Switch the appliance off and on again. If the fault is displayed again, please contact your local Service Force Centre and inform them of the fault code. 23 Malfunction Possible cause Remedy Water tap is blocked with limescale Check the water tap and have it reor faulty. The filter (where present) in the threaded hose fitting on the tap is blocked. [. . . ] Ensure that, if it is necessary to cut off the plug, it is disposed of safely and not retained. 32 Connecting systems The water inlet hose, drain hose and the mains cable must all be connected to the side of the dishwasher as there is no space for them behind the appliance. 2 connection pieces 45° or straight, outer ø 19 mm, length 30 mm double valve waterdrainage water inlet waterinlet mains cable waterdrainage mains socket mains cable 33 Warranty conditions Standard guarantee conditions We, Electrolux, undertake that if within 12 months of the date of the purchase this Electrolux appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: · The appliance has been correctly installed and used only on the electricity supply stated on the rating plate. · The appliance has been used for normal domestic purposes only, and in accordance with the manufacturer's instructions. · The appliance has not been serviced, maintained, repaired, taken apart or tampered with by any person not authorised by us. [. . . ]