User manual AEG-ELECTROLUX ESI682X

[. . . ] Adjusting the height of the upper basket . Selecting the dishwashing cycle (Cycle Table) . If the dishwashing results are not satisfactory . 4 4 6 6 7 8 9 10 12 12 15 16 17 18 20 20 20 21 24 24 25 26 27 28 29 29 30 31 35 Installation and connection instructions. [. . . ] Set the water softener to water hardness range "I". Set the rinse aid dosage to "1". Before the start of the dishwashing cycle put 3in1 detergent in the detergent dispenser. If you do not want to use 3in1 products any more If you want to stop using 3in1 products, please do the following: · Fill up the dispensers for salt and rinse aid again. · Switch the water softener to the highest setting and perform up to three normal cycles without loading any dishes. · Then set the water softener to the water hardness in your area. If you want to use 4in1 products When using "4 in 1" detergents that integrate also anti- glass corrosion agent into "3 in 1" formula, please follow the same indication as given for "3 in 1" detergents. 17 Selecting the dishwashing cycle (Cycle Table) Programme sequence Intermediate rinse Dishwashingcycle Suitable for: Type of soiling Pre-wash Consumption values1) Length (minutes) Energy (kWh) 1, 75 - 1, 95 0, 8 1, 1 - 1, 2 0, 95 - 1, 05 0, 9 Dinner service and cookware 2) heavily soiled, dried-on food remains, in particular protein and starch just used, lightly to normally soiled normally soiled 110 - 120 · · · · Dishes, excluding saucepans Dinner service and cookware - · - · - 30 85 - 95 · · · · · 3) Dinner service and cookware, temperanormally soiled ture-sensitive crockery Dessert dishes and coffee service, delicate glassware lightly soiled 130 - 160 · · · · · 73 - · · · 1) The consumption values were obtained under standardised conditions. They depend on how full the baskets for the dishes are. Variations are therefore possible in practice. 2) When using this cycle, only load the dishwasher half full. 3) Test programme for Test Institutes 18 15 2x 13 - 15 15 - 17 9 23 - 25 2x Water (litres) Main wash Final rinse Drying Selecting a programme When your dishes look like this, select: an intensive programme. a normal or energy-saving programme. a short programme (e. g. 30 minute programme). 19 Starting a dishwashing cycle 1. Check that the spray arms can turn freely. · Occasionally check the internal dispensers, door seal and water inlet filter (if fitted) for dirt and clean them, if necessary. Cleaning the filters 3 The filters must bewillregularly checked and cleaned. Dirty filters spoil the wash results. 1. Open the door and remove the lower basket. Turn the handle about ¼ of a turn anticlockwise (A) and remove the filter system (B). 3. Grasp the grip hole on the fine filter (1) and remove it from the micro-filter (2). Clean all filters thoroughly under running water. 5. Remove the flat filter (3) from the base of the washing compartment and clean both surfaces thoroughly. Place the fine filter in the micro-filter and fit the two together. Insert the filter system in place and lock it by turning the handle clockwise as far as it will go. Ensure that the flat filter does not protrude above the base of the washing compartment. 1 Under no circumstances may the dishwasher be used without its filters. 21 Cleaning the spray arm jets Regularly check the jets in the spray arms for blockages. When cleaning is necessary, remove spray arm from the fixture and clean jets with a pointed object (wire or needle). [. . . ] Connect the threaded hose fitting (ISO 228-1:2000) on the water inlet hose to a tap with an external thread (¾ inch). The inlet hose is fitted with either a plastic or a metal nut: ­ Only tighten the nut hand tight. Then do a visual check for water tightness. (Make sure that the tap is not dripping. ) 1 The water inlet hose must not be kinked, 3 So that accessthe use tap thethe kitchen is not to the in restricted by of dishwasher, we recommend installing an additional tap, or fitting a T-branch to the existing tap. [. . . ]