User manual AEG-ELECTROLUX ESL2435

[. . . ] Contents For the user Safety information Description of the appliance - Spray arm - Coarse strainer/microfilter - Fine filter - Detergent dispenser - Rinse aid dispenser - Water softener For the installer 3 4-5 Technical specifications Unpacking - Damages - Use 15 16 Installation 17-22 The control panel - Switching the buzzer off - Setting the delay start 6 Adjusting the water softener Programme chart Loading and unloading Using the appliance - Starting the programme - Interrupting the programme temporarily - Cancelling the programme - Pause function - Cancelling the drying phase - Switching the dishwasher off 7 8 9 10 - Position - Measurements for fitting a wooden door - Preparing the outer door - Mount plate - Fitting the outer door - Fitting protective and infill strips - Installing the dishwasher - Water inlet - Water drainage - Power supply Information for test centres 23 Maintenance and cleaning Something Not Working Service - Service and Spare Parts - Customer Care Department 11 12 13 Guarantee Conditions 14 Guide to use the instruction book The following symbols will be found in the text to guide you throughout the instructions: Safety information Step by step instructions Hints and tips Environmental information -2- Safety information Before installing and first using the dishwasher, read this instruction booklet carefully, including its hints and warnings. To avoid unnecessary mistakes and accidents, it is important to ensure that all people using the dishwasher are thoroughly familiar with its operation and safety features. Save these instructions and make sure they remain with the dishwasher if it is moved or sold, so that everyone using it through its life can be properly informed on appliance use and safety. q Ensure that the door of the dishwasher is always closed Installation and servicing when it is not being loaded or unloaded. [. . . ] When you want the programme to continue again, press the On/Off button once more and close the door. The programme should not be paused for any longer then necessary, because the water inside the dishwasher has cooled down and must be heated again which increases the power consumption. Cancelling the drying phase In case you do not want to wait until the drying phase is completed, you can cancel it by opening the door. The drying phase is now cancelled. Interrupting the programme temporarily 1. Close the door and the programme continues after about 6 seconds. Open the door carefully when the dishwasher is running, since hot steam may escape which could damage surrounding cabinetry. Switching the dishwasher off Switch the dishwasher off when the buzzer for completed programme sounds (approx. 15 seconds) or the lamp for the completed programme cycle is lit. Open the door and press the On/Off button. Leave the door slightly ajar. Cancelling the programme 1. Press and hold in the combination buttons, the machine goes to starting position and all programme indicator lamps are lit. The programme is now cancelled and a new programme can be selected. If you switch the dishwasher off with the On/Off button, the selected programme is not finished, it is only disrupted. When you start the dishwasher again, the programme will continue. Be careful if you open the door immediately after the programme is finished, since hot steam may escape. This dishwasher is equipped with the new flush system called "IMPULSE WASHING". This washing system varies both the revolutions of the pump and the water pressure for more intensive cleaning of the dishes during a programme. That is why different sections of the programme cycle do not sound the same. - 10 - Maintenance and cleaning Cleaning the filters There are two filters, a coarse one and a fine one which should be cleaned after every wash. Lift out these filters which are in the base of the dishwasher and wash under running water. The dishwasher must not be used without the filters. Incorrect repositioning of the filters will produce poor wash results. Cleaning of the filters is vital to ensure correct operation of the dishwasher. Moving the dishwasher If you have to move the dishwasher (you are moving house, etc): 1. Remove the water inlet and discharge hoses. Avoid tilting the dishwasher during transportation. Cleaning the spray arm The holes in the spray arm must be kept free of scraps for the efficiency of the washing action. When thorough cleaning is necessary, remove the spray arm by unscrewing the nut anti-clockwise, remove the washer and lift off the spray arm. [. . . ] Check that the nut and all other connections are tight before the machine is moved into position. Use only the inlet hose supplied to the dishwasher. Do not reuse an inlet hose used with a previous machine. Water drainage To protect the dishwasher against water damage it is equipped with a water safety system. In the event of a fault the drain-pump starts automatically and the remaining water inside the dishwasher is pumped out. [. . . ]