User manual AEG-ELECTROLUX EU1921C

[. . . ] This appliance is designed to be operated by adults. Children should not be allowed to tamper with the controls or play with the appliance. Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. This appliance should be serviced by an authorized Service Centre, and only genuine spare parts should be used. [. . . ] The power supply cable plug is provided with a contact for this purpose. If the domestic power supply socket is not earthed, connect the appliance to a separate earth in compliance with current regulations, consulting a specialist technician. The Manufacturer declines all responsibility if the above safety precautions are not observed. This appliance complies with EEC directive number 87/308 of 2/6/87 relative to radio interference suppression. This appliance complies with the following E. E. C. Directives: - 73/23 EEC of 19. 2. 73 (Low Voltage Directive) and subsequent modifications; - 89/336 EEC of 3. 5. 89 (Electromagnetic Compatibility Directive) and subsequent modifications. min. 2 50 cm Cleaning the appliance's interior Before using the appliance for the first time, wash the interior and all internal accessories with lukewarm water and some neutral soap so as to remove the typical smell of a brand-new product, then dry thoroughly. Do not use detergents or abrasive powders, as these will damage the finish. 4 Door reversal Before starting work, unplug the appliance. To reverse the opening direction of the door proceed as follows: remove the lower hinge (3), pin (1), insert (4) and foot (2); unscrew the front left foot and screw it back in on the opposite side; remove the two screws which mask the holes for fixing the hinge from the front left hand side; reassemble the door; refit the lower hinge (turning it through 180 ° ), the threaded insert, the pin and the foot on the opposite side, as shown in the figure. Remove the handles, after having removed the screw cover and refit it on the opposite side. The holes that are not used must be masked with the plastic plugs removed. Attention After having reversed the opening direction of the door check that all the screws are properly tightened and that the magnetic seal adheres to the cabinet. If the ambient temperature is cold (i. e. in Winter), the gasket may not fit perfectly to the cabinet. In that case, wait for the natural fitting of the gasket or accelerate this process by heating up the part involved with a normal hairdrier. D548 Fig. 4 4 3 0 18 ¡ 1 2 D547 Fig. 5 B0646 5 USING YOUR FREEZER This freezer has been marked with the symbol, which means that it is suited to the freezing of fresh foods, the conservation of frozen foods and the production of ice-cubes. The control panel max min NS ON SUPER ALARM A Fig. Temperature alarm light Operation Insert the plug into the wall socket. The pilot light will light up, indicating that the appliance is powered. Turn the thermostat knob, clockwise, beyond the « » (STOP) position. To stop the appliance, turn the thermostat knob to position « ». Fast freezing To start fast-freezing food, turn the knob towards «S». Pilot light (D) will come on. Warning light Warning light (E) lights up when the temperature inside the freezer compartment has increased to a value which jeopardizes the long-term storage of food in the compartment. [. . . ] The ice-cubes may be shaken out from the trays by simply twisting; do not use metallic instruments to remove the trays from the freezer. 8 MAINTENANCE Unplug the appliance before carrying out any maintenance operation. Idle periods During periods when the appliance is not used, you should take the following precautions: remove the plug from the wall socket; remove all food from the appliance; defrost and clean the interior and all accessories; leave the door slightly open, thus letting air circulate and preventing the formation of mould and unpleasant smells. Periodical cleaning Never use metal objects for cleaning your appliance as it may get damaged. Wash the interior of the appliance with lukewarm water and sodium bicarbonate. Clean cabinet outer surfaces with a silicone-wax spray. The condenser and compressor should be cleaned using a brush or a vacuum cleaner. [. . . ]