User manual AEG-ELECTROLUX EW1377F

[. . . ] It is dangerous to alter the specifications or attempt to modify this product in any way. All packing and transit bolts must be removed before use. Serious damage can occur to the product and to property if this is not adhered to. Any plumbing work required to install this appliance should be carried out by a qualified plumber or competent person. [. . . ] load Wash at 50 °C 3 rinses Short spin Wash at 30 °C 3 rinses Short spin Draining of water and short spin - Mixed fabrics G 2 kg Worn once H J 2 kg Short spin 2 kg Wool wash K Wash at 40 °C 3 rinses Short spin 1 kg Delicate wash L M Wash at 40 °C 3 rinses Short spin 3 rinses, with fabric softener, if required Short spin 1 rinse, with fabric softener, if required Short spin 2 kg Rinses 2 kg Softeners N 2 kg Drain P Draining of water - - The consumption data shown on this chart is to be considered purely indicative, as it may vary depending on the quantity and type of laundry, on the inlet water temperature and on the ambient temperature. · Programmes G for synthetics and K for wool begin with a short drain, then the programme selector dial advances automatically to the water filling position. · We suggest you not to switch the appliance off and on during its operation. This would modify the memorised programme in progress with unsatisfactory washing results. 15 132984330. qxd 21/07/2005 10:19 Pagina 16 (Nero/Process Black pellicola) Maintenance and Cleaning Before any maintenance or cleaning is carried out you must DISCONNECT the appliance from the electricity supply. Descaling The water we use normally contains lime. It is a good idea to periodically use a water softening powder in the machine. Do this separately from any laundry washing, and according to the softening powder manufacturer's instructions. This will help to prevent the formation of lime deposits. P0010 P0009 Cleaning the drawer recess Having removed the drawer, use a small brush to clean the recess, ensuring that all washing powder residue is removed from the upper and lower part of the recess. Replace the drawer and run the rinse programme without any clothes in the drum. After each wash Leave the door open for a while. This helps to prevent mould and stagnant smells forming inside the appliance. Keeping the door open after a wash will also help to preserve the door seal. Maintenance Wash With the use of low temperature washes it is possible to get a build up of residues inside the drum. We recommend that a maintenance wash be performed on a regular basis. Clean the filter using a hard bristle brush. Tighten up the inlet hose. P1090 17 132984330. qxd 21/07/2005 10:19 Pagina 18 (Nero/Process Black pellicola) Something Not Working Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without calling out an engineer. Before contacting your local Service Force Centre, please carry out the checks listed below. IMPORTANT: if you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is under guarantee. Symptom The machine does not start Possible causes The door has not been closed. The plug is not properly inserted in the power socket. There is no supply at the socket The main fuse or the fuse in the plug has blown. The selector dial is not correctly positioned The ON-OFF button has not been depressed. The filter in the inlet hose is blocked. The inlet hose may be squashed or kinked. The end of the drain hose is submerged in water. There is no vent in the end of the drain hose. [. . . ] C) depends on the height of the adjacent furniture's base. 35 Ø 12. 5-14 depth 16 -22 B 416 22+1 515 176, 5 596 570 min. 820 min 59 8 5-59 C , 5 818 416 120 P0422S C 54 8 1 195 160 P0965 90 0 49 A When installing the appliance into the kitchen furniture ensure, if possible, the hoses are placed in either of the two recesses on the back of the appliance. This will help to prevent the hoses from becoming kinked or trapped. Picture AB. b) Hinges To mount the hinges it is necessary to drill two holes (dia. 35 mm, depth 12. 5-14 mm depending on the depth of door furniture) on the inner side of the door. [. . . ]