User manual AEG-ELECTROLUX EWT136451W

[. . . ] Do not machine wash clothes with ribbing, unfinished or torn material. iNSTALLATION · Unpack or ask for the appliance to be unpacked immediately upon delivery. Check the outside of the appliance is not damaged in any way. Report all transit damage to your retailer. [. . . ] SELECTING OPTIONS You must select the different options after selecting the programme and before presspushbutton (see ing the "Start/Pause" "Programme table"). press the desired button(s) ; the corresponding lights come on. If one of the options is not compatible with the selected programme, "Err" flashes on the dispushbutton play and the "Start/Pause" flashes red. "PREWASH" OPTION The appliance runs a prewash at 30°C max. "RINSE PLUS" OPTION The washing machine will add one or more rinses during the cycle. This option is recommended for people with sensitive skin and in soft water areas. Permanent : Hold down the "Prewash" and "Delay Start" pushbuttons for a few seconds. "DELAY START" This option allows you to delay the start of a wash programme by 30, 60, 90, 2 hours to 20 hours. the selected time appears on the display for a few seconds. You can change or cancel the delayed start time at any time before you press the Load the washing, close the drum and the lid of your washing machine. Before closing the lid of your appliance, ensure that the drum is properly closed : · When the two shutters are closed, · locking button A released. PROPORTIONING OF DETERGENTS Pour the amount of washing into the washand prewash compartments if ing you have selected the "prewash" option. If you turn the programme selector to another programme while a cycle is in progress, the appliance will ignore the new selected programme. If you have already pressed the "Start/ pushbutton and you want to Pause" change or cancel the delayed start, proceed as follows : · To cancel the delayed start and start the cycle immediately, press "Start/Pause" and then "Delay start" . To change the timer delay period, you position must go through the "Stop" and reprogramme your cycle. the lid will be locked during the delayed start time. If you need to open it, you must first pause the appliance by pressing the pushbutton. After closing "Start/Pause" the lid again, press the "Start/Pause" pushbutton. TIME MANAGER The cycle can be made longer or shorter by pushbuttons. Using the "Time Manager" The level of soiling of the laundry is also indicated. It is normal for the programme selector to remain stationary during the cycle. WARMING UP During the cycle, the symbol comes on when the appliance is reaching the right temperature. [. . . ] The appliance fills but empties straight away : The washing machine doesn't rinse or doesn't empty : You have found water around the washing machine : All packaging have not been removed from the appliance (see installation section), · the appliance isn't level and is unbalanced , · The appliance is too close to the wall or furniture, · washing is unevenly distributed in the drum , · The load is too small. The water inlet filters are dirty, the power or water supply has been cut off, the motor overheating detector has been activated, the water inlet temperature is lower than usual, the foam detection security system has been activated (too much detergent) and the washing machine has begun draining the foam, · The out of balance detector has been activated: an extra phase has been added to distribute washing more evenly in the drum. The "immediate opening"1) light is not lit, · The temperature inside the drum is too high, · The wash cycle is much too long : The washing machine stops during a wash cycle : The lid doesn't open at the end of the cycle : The E40 error code appears in the display2) and the "Start/Pause" pushbutton flashes red 3) : Electrolux 23 Problems The E20 error code appears in the display2)and the "Start/Pause" pushbutton flashes red3): The E10 error code appears in the display2) and the "Start/Pause" pushbutton flashes red3): The EF0 error code appears in the display2) and the "Start/Pause" pushbutton flashes red3): Softener runs directly into the drum when filling the dispenser box: · The anti-flooding security system has been activated, please proceed as follows : - close the water inlet tap, - empty the appliance for 2 minutes before unplugging, - call the after-sales service. 2) On some models, the auditable signals can sound 3) After solving any problems, press "Start/Pause" pushbutton to restart the interrupted programme. [. . . ]