User manual AEG-ELECTROLUX EXI12HA1WE

[. . . ] SERVICE MANUAL MIDEA AIRCONDITIONER DC INVERTER SPLIT WALL-MOUNTED TYPE MSC-09HRDN1-QD0(E) MSC-12HRDN1-QC6(E) MSH-09HRDN1-QD0(E) MSH-12HRDN1-QC6(E) V1. 2 Apr. , 2007 CONTENTS 1. Precaution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1. 1 Safety Precaution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1. 2 Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Open the low-pressure valve on the charge set slightly to purge air from the charge hose. Set the 2-way valve to the close position. Operate the air conditioner at the cooling cycle and stop it when the gauge indicates 0. 1MPa. Immediately set the 3-way valve to the closed position. Do this quickly so that the gauge ends up indicating 0. 3 to 0. 5Mpa. Disconnect the charge set, and amount the 2-way and 3-way valve's stem nuts and service port caps. Use a torque wrench to tighten the service port cap to a torque of 1. 8 kgf. m. Be sure to check for gas leakage. 15 7. 6 Re-air purging (Re-installation) Procedure: 1. Confirm that both the 2-way and 3-way valves are set to the closed position. Connect the charge set and a charging cylinder to the service port of the 3-way valve. Leave the valve on the charging cylinder closed. Open the valves on the charging cylinder and the charge set. Purge the air by loosening the flare nut on the 2-way valve approximately 45' for 3 seconds then closing it for 1 minute; repeat 3 times. After purging the air, use a torque wrench to tighten the flare nut to on the 2-way valve. Check the flare connections for gas leakage. Close the valve on the charging cylinder and discharge the refrigerant until the gauge indicates 0. 3 to 0. 5 Mpa. Disconnect the charge set and the charging cylinder, and set the 2-way and 3-way valves to the open position. Be sure to use a hexagonal wrench to operate the valve stems. Mount the valve stems nuts and the service port cap. Be sure to use a torque wrench to tighten the service port cap to a torque 18N. m. Be sure to check the gas leakage. 16 7. 7 Balance refrigerant of the 2-way, 3-way valves Procedure: 1. Confirm that both the 2-way and 3-way valves are set to the open position. [. . . ] YES Is voltage being applied to the fan motor?(rang 90v-160v between mid pin and N on CN1 NO Repair the connector and reconnect YES Indoor PCB is defective. Replace the indoor PCB. NO Replace the indoor fan motor 10. 3. 5 E5(Open or short circuit of outdoor temperature sensor) diagnosis and solution. Is the outdoor temperature sensor connector and connection good?YES Replace the sensor and check if E5 display again? [. . . ]