User manual AEG-ELECTROLUX EXQUISIT200.8

[. . . ] Avoid pulling the appliance or suction brush over the mains lead. The cover cannot be closed if a paper filter is not inserted. Always ensure that a paper filter as well as a MICRO. ILTER and a motor protection filter are inserted. This vacuum cleaner may only be used for vacuuming dry materials in households. [. . . ] . irmly connect the suction tube handle to the suction tube. Connect the Suction Tubes Together (depending on model) Connect the two tubes together. Mains Connection/Cable Rewind The mains cable is stored in the cable compartment. Pull out the cable and plug into a mains socket. Press the foot button, the cable is automatically rewound after vacuuming. Adjust the Telescopic Tube (depending on model) Push down the button on the tube and adjust the tube to the desired working position. 12 Using the Nozzles The nozzles are connected to the suction tube by pressing and turning, and removed by pulling and turning. Crevice Nozzle . or vacuuming crevices, gaps and corners. Using the VARIO 500 . loor Nozzle . or daily care of carpets and hard floors. The floor nozzle is manually adjustable. Extended brushes for smooth floors, retracted brushes for carpets. See additional accessories for special floor nozzles. Upholstery Nozzle . or vacuum cleaning all upholstered furniture, mattresses, etc. The thread lifting strips on the nozzle even pick up thread and lint. Crevice and Upholstery Nozzle Stored in the Appliance To meet individual cleaning requirements two accessories are included with the appliance, these are stored in an integrated accessories compartment. Open the lid of the accessories compartment upwards at the recessed handle. The nozzles can be fitted to both the suction tube and the suction hose handle as required. 13 Switching On Switch On and Off The appliance is switched on and off by pressing the On/Off button. mum power. The Mega-Power indicator lamp lights up for as long as the Mega-Power stage is activated. In this power stage, the adjustment wheel only has the function of the on / off switch. Power adjustment is not possible in this stage. Power Regulation*: Maintenance and Cleaning Be sure that the appliance is turned off and that the mains plug has been removed from the socket before performing maintenance or cleaning. Power Regulation Rotary Regulator The suction power can be adjusted to suit the specific situation using the electronic power regulator. Changing the Paper . ilter The paper filter must be replaced if the window on the filter replacement indicator is completely red when the appliance is operating at maximum power and the nozzle is raised from the floor. The paper filter should be replaced even if it does not appear to be full because fine dust can block the pores in the surface of the filter. Output control, Mega-Power A Switching on and off. Switch on you vacuum cleaner with the power adjustment wheel by turning the power adjustment wheel in the direction of the arrow º max. The operating lamp indicates that the vacuum cleaner is connected to the mains voltage and is ready for operation. With the power adjustment wheel you can set the power of your vacuum cleaner to the optimum value for the relevant cleaning work. NOTE: If the power adjustment wheel is turned fully to the right, this setting gives you a strong suction, economical power setting for most cleaning work. Press the Mega-Power button for cleaning work which requires a particularly high suction power. The vacuum cleaner then runs at maxi- The cover can be opened by pressing the button and folding back until it locks. *depending on model 14 Changing the Microfilter We recommend replacing the microfilter on every fifth paper filter replacement, at the latest when the dust level indicator is completely red with a clean dust bag and the nozzle raised. Hygiene filter replacement: When removing the full filter bag, pull the closing tab to automatically close the bag. During this process you must overcome slight resistance when pulling the tab. [. . . ] As a result, at the lowest power setting the appliance may have a start delay of approx. 4 seconds. Carrying and Storage To make the appliance easier to store and carry, slide the floor nozzle into the tool rail. Parking System . or storing the suction tube and nozzle during short pauses in use. The bracket on the nozzle is slid into the parking rail on the appliance. . . . the thread lifters are worn If the thread lifters on the suction inlet are worn or matted, you can replace them with new thread lifters. [. . . ]