User manual AEG-ELECTROLUX EXS18HC2WI

[. . . ] EXAMPLE OF TIMER SETTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ADJUSTING AIR FLOW DIRECTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 3 4 5 6 7 8 8 9 10 11 REMOTE CONTROLS AND THEIR FUNCTIONS Mode select button ON/OFF button TEMP Each time you push the button, a mode is selected in a sequence that goes from AUTO, COOL, DRY, HEAT (cooling only type without), FAN ONLY and back to AUTO. CLOCK C SPEED Push the button to start operation, push the button again to stop operation. MODE ON TEMP. FAN SPEED Temperature button OFF Fan speed button This button is used for selecting fan speed. Each time you push the button, a fan speed is selected in a sequence that goes from AUTO, LOW, MED, HIGH, and back to AUTO. : The set temperature is increased to 30¡£ C : The set temperature is decreased to 17¡£ C TEMP CLOCK C SPEED MODE FAN SPEED ON TEMP OFF Slide the cover 1 REMOTE CONTROLS AND THEIR FUNCTIONS Wind directory button Push this button to change the swing angle of louver. (This is not conform to the unit without this function. ) Auto louver button Push this button to swing louver. [. . . ] If you do not use the remote controller for more a few weeks, remove the batteries. Otherwise, battery leakage may damage the remote controller. The average battery life during normal use is approximately half a year. Replace the batteries when there is no receiving beep from the indoor unit or if the transmission indicator on the remote controller fails to light. SETTING THE CLOCK AUTO COOL DRY HEAT FAN TEMP CLOCK TIMER ON TIMER OFF SPEED Before you start operating the air conditioner, set the clock of the remote controller using the procedures given in this section. The clock panel on the remote controller will display the time regardless of whether the air conditioner is in use or not. Initial Setting or the Clock When batteries are inserted in the remote controller, the clock panel will display "0:00" and the colon will flash. Time adjust button (TIME ADJUST) push this button to set time. Each time you push the button, the time moves forward or backward by one minute depending on which side you Push. The time alters as quickly as you push the button. . AUTO LOW MED HIGH MODE ON TEMP FAN SPEED OFF AIR DIRECTION ECONOMIC RUNNING 2 3 SWING OK CANCEL TIMER ON CLOCK TIMER OFF TIME ADJUST 1 5 2. OK button. Clock When you push the OK button, the clock time display stops flashing and the clock starts operating. 3. Readjusting the Clock Push the CLOCK button in the battery compartment, the colon in the clock display will start to flash. To set the new time, follow 1 and 2 of "Initial Setting of the Clock". * Clock accuracy is within 10 seconds per day. CAUTIONS Static electricity or other factors (in case of extremely high voltage) can cause remote controller clock initialise. If your remote controller is initialized (flashing of the colon in "0:00"), readjust the clock before you start operation. LOCK AND RESET BUTTON FUNCTION 1. When you push the LOCK button, all current settings are locked in and the remote controller does not accept any operation except that of the LOCK button Use the lock mode when you want to prevent settings from being changed accidentally or playfully. Push the LOCK button again when you want to cancel the LOCK mode. When you push the RESET button, all current settings are cancelled and get into the condition of beginning. In the clock, the colon in "0:00" will flash, the mode displays "Auto", fan speed displays "Auto", the temperature displays "24". AIR DIRECTION ECONOMIC RUNNING SWING OK CANCEL TIMER ON CLOCK TIMER OFF TIME ADJUST 12 6 AUTOMATIC OPERATION AUTO COOL DRY HEAT FAN TEMP CLOCK TIMER ON TIMER OFF SPEED AUTO LOW MED HIGH 1 3 MODE ON When you set the air conditioner in AUTO mode, it will automatically select cooling, heating (cooling only type without), or fan only operation depending on the room temperature. Once you select the operating mode, the operating conditions are saved in the unit's microcomputer memory. Thereafter, the air conditioner will start operating under the same conditions when you simply push the ON/OFF button of the remote controller. 2 TEMP . FAN SPEED Start The OPERATION lamp on the display panel of the indoor unit starts flashing. Temperature button (TEMP . ) Set the desired temperature. Normally, set it between 21 C to 28 C 3. ON/OFF button Push this button to start the air conditioner. The OPERATION lamp on the display panel of the indoor unit lights. The operating mode is selected in accordance with the room temperature and operation starts after approximately 3 minutes. [. . . ] Push the SWING button on the remote controller. To stop the function, push the SWING button again. To change the swing direction, push the AIR DIRECTION button. CAUTIONS The AIR DIRECTION and SWING buttons will be disabled when the air conditioner is not in operation (including when the ON TIMER is set). Do not operate the air conditioner for long hours with the air flow direction set downward during the cooling or dry operation. [. . . ]