User manual AEG-ELECTROLUX F50671

[. . . ] To ensure optimal and regular performance of your appliance please read this instruction manual carefully. It will enable you to navigate all processes perfect ly and most efficiently. To refer to this manual any time you need to, we recommend you to keep it in a safe place. And please pass it to any future owner of the appliance. [. . . ] (Follow manufacturer's instructions!) If your water hardness is higher than that recommended by the manufacturer but you would nevertheless like to use 3in1 detergent, proceed as follows: With the 3in1 function selected, set the water softener one hardness setting lower than when rinsing without 3in1 detergent. Fill up the dispenser (if this is empty) with special salt. The dishwasher remembers the two different settings of the degree of hardness for rinsing with and without 3in1 function. 3 In daily use 21 Activation/deactivation of the 3 in 1 function Press simultaneously the two buttons positioned over the writing Multitab, un til the "Multitab function "indicator light illuminates. This means that the func tion is active. To deactivate the function press the same buttons again until the indicator light corresponding to the "Multitab" symbol turns off. 3 As the rinse aid inflow is automatically switched off when the 3in1 function is activated, it may come about because of the different quality standards in the 3in1 detergent, that the dishes do not dry sufficiently. If this happens, proceed as follows (see section "Adding rinse aid"): Fill up the dispenser (if this is empty) with rinse aid. Set rinse aid dosage to "2" mechanically. If you do not want to use 3in1 products any more If you want to stop using 3in1 products, please do the following: Deactivate the 3in1 function. Fill up the dispensers for salt and rinse aid again. Switch the water softener to the highest setting and perform up to three nor mal cycles without loading any dishes. Then set the water softener to the water hardness in your area. To change the time delay: As long as the cycle has not yet started, you can still change the setting by pressing the DELAY TIMER button. In daily use 25 Cancelling the delay timer: Press the Delay Timer button repeatedly until the Multi display goes out. The se lected dishwashing cycle will begin immediately. To change a dishwashing cycle As long as the cycle has not yet started, you can still change the dishwashing cycle. First abort the dishwashing cycle, then re set the time delay, lastly select the new dishwashing cycle. Switching off the dishwasher Do not switch off the dishwasher until the indicator for the end of the dish washer cycle is illuminated in the cycle progress display. Therefore leave the dishes to cool for about 15 minutes before removing them. Dishes dry more quickly if you open the door for a moment after the cycle has ended and then leave it slightly open. 1 Removing the dishes 3 It is normal for the inner door and the dispensers to be damp. Empty the lower basket first, then the upper basket. This way you avoid drip ping water from the upper basket onto dishes in the lower basket. 26 Care and cleaning Care and cleaning 1 Do not use furniture care products or aggressive cleaners. When necessary, clean the dishwasher's controls with a soft cloth and clean warm water. Occasionally check the internal dispensers, door seal and water inlet filter (if fitted) for dirt and clean them, if necessary. Cleaning the filters 3 The filters must be regularly checked and cleaned. Dirty filters will spoil the wash re sults. [. . . ] Minimum required height: 40 cm above the bottom edge of the appliance. 36 Connecting the dishwasher Extension hoses Extension hoses are available from your dealer or from our Customer Care Depart ment. To ensure that the function of the appliance is not impeded, the internal di ameter of extension hoses must be 19 mm. Extension hoses must not be laid more than a maximum distance of 4 metres horizontally; the maximum permitted height for the connection for the drain hose is then 85 cm. Sink outlet connection The outlet of the drain hose ( 19 mm) fits all commonly available sink outlet types. The outer diameter of the sink outlet connection must be at least 15 mm. [. . . ]