User manual AEG-ELECTROLUX FAV50460U

[. . . ] and please pass it to any future owner of the appliance. We wish you much joy with your new appliance. OPERATING INSTRUCTIONS IMPORTANT SAFETY INFORMATION ENVIRONMENT INSTALLATION Appliance positioning Removing transport safety packaging Electrical connection Changing door stop Special accessories PRODUCT DESCRIPTION CONTROL PANEL Control panel Display BEFORE FIRST USE PROGRAMME OVERVIEW DAILY USE Sorting laundry Average laundry weights Switching machine/drum light on Laundry loading Selecting the programme 76 76 78 79 79 79 80 80 81 82 83 83 83 84 84 85 85 86 86 87 87 DELICATE (SCHON) function 87 LONG ANTI-CREASE (KNITTERSCHUTZ PLUS) function 87 BUZZER (SIGNAL) function 88 TIME (ZEITWAHL) function 88 DELAY START (ZEITVORWAHL) 88 Child lock 88 Starting the programme 89 Changing programme 89 Drying cycle complete / removing laundry 89 CARE AND CLEANING 90 Cleaning fluff filter 90 Cleaning the door seal 91 Emptying the condensate tank 91 Cleaning heat exchanger 92 To clean the drum 93 Clean operating screen and housing 93 WHAT TO DO IF . 94 MACHINE SETTINGS TECHNICAL DATA SERVICE 95 96 97 Subject to change without notice In the interest of your safety and to ensure the correct use, before installing and first using the appliance, read this user manual carefully, including its hints and warnings. [. . . ] A B Unscrew hinge A from the front of the appliance and take off the loading door. To do this, inB A sert a thin screwdriver into the slots as shown in the illustration, push downwards slightly and pry out the cover plates. Use an appropriate tool and exert pressure to unfasten locking block C from the snapon fixture, take out and re-insert on the other side having rotated the block through 180°. Unscrew hinge A from the loading door, rotate through 180°, re-insert on the opposite side and screw down. Re-insert cover plates B on the opposite site having first rotated them through 180°. Unscrew cover plates D from the front D E of the appliance, rotate through 180°, F F screw on the opposite side. Unscrew door lock E , push down slightD ly and remove from the front of the appliance. Push snap-in button F in and down, push cover down slightly and remove from front of the appliance. Change door lock E over to the opposite side, screw down the door interlock. On the other side, insert cover F and allow snap-in button to lock into place. Insert loading door and hinges into recesses on the front of the appliance and screw down. Turn items with double-layered fabrics inside out (e. the child lock function locks all buttons and the programme knob. The child lock can be activated or deactivated by holding ­ Before programme is started: Appliance cannot be used ­ After programme is started: Programme in operation cannot be changed The icon appears in the display to indicate that the child safety device is activated. The child safety device is not deactivated once the programme comes to an end. If you want to set a new programme, you must first deactivate the child safety device. To change a programme which has been selected by mistake once the programme has started, first turn the programme selector to OFF (AUS) and then reset the programme. The programme can no longer be changed directly once the programme has started. The drying programme is not however affected by this (laundry protection). Once the drying cycle is complete, display shows a blinking . If the BUZZER (SIGNAL) button has been pressed, an acoustic signal sounds intermittently for about one minute. The drying cycles are automatically followed by an anti-crease phase which lasts around 30 minutes. [. . . ] The special bulb can be obtained from your local service centre. When the appliance is switched on, the interior lighting switches itself off after 4 minutes when the door is open. These develop too much heat and may damage the appliance!Before replacing the bulb, disconnect the mains plug; with a permanent connection: fully unscrew or deactivate the fuse. [. . . ]