User manual AEG-ELECTROLUX FAV50730-W

[. . . ] It is essential that this information is observed. This symbol guides you step by step when operating the appliance. Next to this symbol you receive additional in- formation and practical tips on using the ap- pliance. Tips and information about the economical and environmentally friendly use of the ma- chine are marked with the clover. [. . . ] For a period of 5 seconds it is possible to change to another programme, and also to select the Eco but- ton or the Half Load button. After each press of a button, there is a period of 5 seconds during which any corrections can be made. Do not open the door after the program has started!To prevent scolding and damage to units by escap- ing steam. Half load Mains switch Economy 15 Program display The illuminated symbols in the display indicate which phase of the program is currently running. Pre-rinse Cleaning Rinsing Drying Program end Remaining running time As soon as a program starts, the time remaining lights up in the display field in minutes. This time varies de- pending on the loading and temperature of the incom- ing water. The display may remain at one time for sevral minutes. It may also jump in time this quite normal, and does not indicate a fault. End of the program The illumination of a "0" in the start delay display and the program end symbol in the program display indi- cate the end of the washing program. Safety lock The safety lock prevents an accidental restart after the end of the program. In order to be able to enter a new program, the dishwasher must either be switched off and then on again, or the door must be opened and then closed again. The safety lock is released as soon as only the Programme End symbol is illuminated in the programme display. Delay start The start of the selected program can be delayed bet- ween 1 and 9 hours in steps of 1 hour using the Start Time Pre-selection button. - By repeatedly pressing the button, the delay time can be programmed in hours, and will be displayed in the display field. Display: Hours and a small "h". 16 A washing program can be selected first, and then the pre-selected start time can be pro- grammed, or vice versa. If a fault occurs, an error code in the display, one of the program control lamps and the Program End symbol in the display will blink. Please note down this error code before making con- tact your Service Centre. The error message is deleted by switching off the main switch. Start time / Remaining time display Programme sequence display Mains switch Error codes and possible causes A = Water tap closed, inlet hose filter blocked C = Drain hose, coarse or fine strainer or sink trap blocked E = Water pressure too low, water tap not comple- tely opened, inlet hose or inlet hose filter is blocked, machine losing water. E2 = Call AEG Service force H = Call AEG Service force L = Call AEG Service force Unloading the crockery basket After the washing program is complete: 1. Then unload the upper basket, so that no drops of water fall onto the dry crockery in the lower basket. Inspect the coarse strainer after every washing sequence. Clean as necessary. 19 Cleaning and care Internal Cleaning Ensure that the seals around the door, the detergent and rinse aid dispensers are cleaned regularly with a damp cloth. We recommend the use of Finish Dishwasher Cleaner, every 3 months or run a 65oC wash without dishes using detergent. Regular use of Finish Dishwasher Cleaner cleans inaccessible parts, eliminates unplea- sant food odours and helps prevent the build-up of li- mescale. Re-filling the salt dispenser Never fill the salt dispenser with rinsing aids or detergents!When the salt replenishment lamp lights up, you must refill the special salt for the water softener. Proceed as described in the "Using for the First Time" chapter on page 8, however you do not need to add any water during this process. Immediately after refilling, run the "Pre-rinse" program to wash away any salt residues. Refilling the rinse aid Upon lighting up of the rinse indication you should re- fill rinse. [. . . ] The wires on the mains lead are coloured in accordance with the following code. Green and Yellow -Earth Blue -Neutral Brown -Live The wired coloured green and yellow must be connec- ted to the terminal marked with the letter "E" or by the earth symbol or coloured green and yellow. The wired coloured blue must be connected to the ter- minal "N" or coloured black. The wire cooured brown must be connected to the ter- minal marked "L" or coloured red. [. . . ]