User manual AEG-ELECTROLUX FAV6281IB

[. . . ] Gebrauchsanweisung , Notice d'utilisation et d'installation, Installatie- en gebruiksaanwijzing EFP 6410 EFP 6430 User manual, Instrucciones de montaje y manejo, Manual de Instruções D F NL UK E P Contents UK Safety warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 For the installer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 For the user . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Attention: the metal grease filters must be removed and washed, either by hand or in the dishwasher, every four weeks. Open the metal grease filter Pull the lateral handles towards the bottom, by placing them in the front and removing the filter. Hand washing Soak grease filters for about one hour in hot water with a little washing-up liquid, then rinse off thoroughly with hot water. Refit the grease filters when they are dry. Dishwasher Place grease filters in the dishwasher. Select most powerful washing programme and highest temperature, at least 65°C. Refit the grease filters when they are dry. When washing the metal grease filter in the dishwasher a slight discolouration of the filter can occur, this does not have any impact on its performance. Clean the inner housing using a hot detergent solution only (never use caustic detergents, abrasive powders or brushes). Fig. 3 42 Charcoal filter The charcoal filter should only be used if you want to use the hood in the recirculation function. To do this you will need an original ELECTROLUX charcoal filter (available from your local Service Force Centre). 610 899 421 The charcoal filter must normally be replaced at least once every year. This filter cannot be washed or regenerated. To guarantee proper absorption of odours the working volume of the charcoal must be proportionate to the hood air flow. In this case the high quality of the charcoal will ensure efficient odour removal for approximately one year, assuming that the hood is used normally. For this reason you should always use original AEG filters only, making sure they are replaced when necessary. Remove first the rear then the front grease filters. Insert the charcoal filter into the lugs of the holding frame above using the 2 red clips to retain it below, press the red clips inwards, and insert the charcoal filter in the holding frame. Press both red lugs upwards (towards the inside of the housing) and remove the charcoal filter downwards. Clean the internal housing only with warm washing-up liquid suds (never use any abrasive cleaners, brushes, or scouring agents). Always specify the hood model code number and serial number when ordering replacement filters. This information is shown on the registration plate located on the inside of the unit. [. . . ] The following is valid in the United Kingdom only: - the wire which is coloured green and yellow must be connected to the terminal which is marked with the letter E or by the earth symbol ), or coloured green or green and yellow; ( - the wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black, - the wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. 47 Installation Mounting accessories included 1 deflector 4 spacer discs 2 metal screws 2, 9x13 4 wood-screws 4, 5 x 16 mm 1 flange Ø 120 mm 1 allen spanner (for TORX screws) Preparing the wall unit - Extractor version The hood is supplied as an extractor unit. Before installing the hood, drill a hole in the roof of the wall unit (see fig. This hole is to allow passage of the outlet pipe and the power cable, and to facilitate servicing. The wall unit must have a minimum body depth (without door) of 300 mm with recessed light screen and min. [. . . ]