User manual AEG-ELECTROLUX FAV64070UM

[. . . ] FAVORIT 64070 U Dishwasher User information Dear customer, Please read this User Information carefully and keep it to refer to at a later date. Pass this User Information on to any subsequent owner of the appliance. 1 3 2 The following symbols are used in the text: Safety instructions Warning: Notes that concern your personal safety. Attention: Notes that show how to avoid damage to the appliance. Useful tips and hints Environmental information 3 Your dishwasher is fitted with the new "PULSE WASH" dishwashing system. [. . . ] Place the coarse and fine filters in the micro-filter and press together. Insert the filter system in place and lock it by turning the handle clockwise as far as it will go. Ensure that the flat filter does not protrude above the base of the washing compartment. Under no circumstances may the dishwasher be used without its filters. 1 22 What to do if. . . Remedying small malfunctions If one of the following fault codes is displayed in the multi-display during operation: ­ Fault codeÅ 10 (Problems with water inlet), ­ Fault codeÅ 20 (Problems with water drainage), please have a look at the following table. When the fault is remedied, press the button for the cycle that has started. With other fault codes ("Å " followed by a number): ­ Abort the dishwashing cycle. ­ Switch the appliance off and on again. If the fault is displayed again, please contact the Customer Care Department and inform them of the fault code. Malfunction Possible cause Water tap is blocked with limescale or faulty. Remedy Check the water tap and have it repaired if necessary. Turn the tap on. The cycle indicator for the selected dishwashing cycle is flashing: fault code Å 10 is displayed in the multi-display: (Problems with water inlet) The filter (where present) in Clean the filter in the the threaded hose fitting threaded hose fitting. Press the button for the commenced dishwashing cycle; then abort the dishwashing cycle (see section: Starting a dishwashing cycle); clean filters (see section: Cleaning the filters). Filters in the base of the dishwasher compartment are blocked. Water inlet hose Check the position of the has not been correctly posihose. tioned. 23 Malfunction The cycle indicator for the selected dishwashing cycle is flashing, fault code Å 20 is displayed in the multi-display. (Problems with water drainage) Fault code Å 30 is displayed in the multi-display. Possible cause The sink outlet is blocked. Remedy Clean out sink outlet. Water drain hose Check the position of the has not been correctly posihose. tioned. The anti-flood system has been triggered. The mains plug is not plugged in. First shut off the water tap, then switch off the appliance and contact the Customer Care Department. Plug in mains plug. The cycle is not starting. A fuse in the house's wiring Replace fuse. For dishwasher models with If the dishes are to be a delay start timer: washed immediately, cancel A start time has been sethe delay start. lected. The dishwashing compartment is made from rustfree stainless steel. Rust spots in the dishwashing compartment are due to Rust spots are visible in Only wash cutlery, dishes rust particles from external the dishwashing compartand pans that are suitable sources (rust particles from ment. Remove such spots with a commercially-available stainless steel cleaning product. A whistling noise can be The whistling is not a cause Use a different brand of deheard when washing dishfor concern. es. 24 If the dishwashing results are not satisfactory The dishes are still dirty. [. . . ] Box 539 Tripoli 37 Estonia Electrolux Estonia Ltd. Mustamäe tee 24 EE0006 Tallinn Tel. : (372) 6 650 090 Fax: (372) 6 650 092 Hongkong Wo Kee Services Ltd. 585-609 Castle Peak Road Kwai Chung N. T. Hongkong Tel. : 2494 4000 Israel Electricity & Electronic Services-Evis LTD. [. . . ]