User manual AEG-ELECTROLUX FM7531KAN

[. . . ] INSTRUCTION BOOK FM 7531K-an GB 325 88-8450 rev. 3-343 949 601 403 Your New Appliance Thank you for purchasing an AEG appliance. To enable you to use your new appliance efficiently and safely, please read this instruction book carefully before installing or using the appliance, and retain for future reference. Should the appliance be transferred to a new owner please ensure this instruction book is left with the appliance in order that the new owner can get to know the functions of the appliance and the relevant warnings. [. . . ] When a pan is placed on a cooking zone, its material will be registered. The cooking zone will only heat up if the pan is made of metal. If the pan or whatever placed on the zone is not made of metal, the cooking zone will not heat up. The display will show "F". The hob surface gets hot. . . . . . . . . . . . . . . . . The fuses are constantly blowing. . . . . The cooking zones don't get hot enough Automatic zone registration For double and triple zones, the circuits matching the pots being used will automatically be switched on. Registration depends on the material and size of the pot. 10 31 Overview of the outside width of the units 180 mm Downdraft 360 mm Glass ceramic hob with 2 cooking zones Gas hob with 2 burners Induction hob with 2 cooking zones Grill Grill / Fryer Wok 580 mm Glass ceramic hob with 4 cooking zones Gas hob with 4 burners 720 mm Glass ceramic hob with 4 cooking zones Gas hob with 4 burners Induction hob with 4 cooking zones Cooking Zones The cooking zones can be adjusted from 0-9, where 9 is the highest setting. Push the 2. zone you wish to use. k key. Push l or m key to adjust the The zones must be adjusted within 10 seconds or the hob turns off again. By pushing the key the cooking zone is adjusted in steps from 0-9. key the cooking By pushing the zone is adjusted in steps from 9-0. or By continuously pushing the key the adjustment goes faster the steps from 1-9 are run through. m l m l Turn off a single zone by pushing the keys simultaneously until the display shows "0". lm Turn off all zones by pushing the key. k 30 11 Residual Heat Indicator Each cooking zone has a residual heat indicator. When the cooking zone is turned off the "H" is lit up in the display until the cooking zone has cooled. "H" is a warning that the cooking zone is still hot. To optimise joints between the installed hobs, the gap between the ceramic hob may be grouted with silicone: 1. Remove the aluminium panels from the hobs. Apply a stripe of silicone to the gap between the two ceramic hob. Use only the silicone supplied, as it is designed to tolerate the appliance's high temperature. Splash a little soapy water (washing-up liquid) on the silicone stripe 4. Press the rubber block hard against the ceramic hob and pull it slowly from back to front (Fig. Leave the silicone to harden until the next day. Remove surplus silicone coating from the ceramic hob with the razorblade supplied. Be careful not to damage the silicone in the gap. Run tools only along the joint, never across it. Polish the ceramic hob with the supplied cleaning product for ceramic hobs. Automax With AUTOMAX you do not need to turn down the temperature. [. . . ] In the display it will say "0". After a few seconds the display will turn off. lm 22 19 Choice of Pans Pans used on the glass ceramics must: - Completely cover the cooking zone, and may be slightly larger than the cooking zone - Have a plane bottom or at most curve slightly inward (max. 1 mm) as the bottom on heating up will curve outwards - Be thick-bottomed - Aluminium pans must minimum have a 3, 5 mm thick bottom - Steel pans and frying pans must minimum have a 5 mm thick bottom - Have a completely smooth or finely patterned bottom Check that the planeness of the pans by placing it upside down on a table top and holding a ruler on the bottom of the pan. A concave as well as a convex bottom prolong the cooking time and increases the energy consumption. [. . . ]