User manual AEG-ELECTROLUX GK29TCICN

[. . . ] We promise that it will provide a superior User Experience delivering Ease-of-Mind. Good luck! 4 electrolux contents Contents Safety instructions 5 Description of the Appliance 7 Operating the appliance 10 Tips on Cooking and Frying 19 Cleaning and Care 22 What to do if . . . 24 Disposal 26 Installation Instructions 27 Built-in installation 29 Installation proud of the work surface31 Garantie/Kundendienst 37 Service 38 The following symbols are used in this user manual: 1 3 2 Important information concerning your personal safety and information on how to avoid damaging the appliance. General information and tips Environmental information safety instructions electrolux 5 Safety instructions Children's safety · Small children must be kept away from the appliance. [. . . ] Control panel Switch on the appliance (Do not set a heat setting) Touch Touch until the signal sounds Acoustic signal Display/Signal Appliance switches off. Releasing the child safety device Step 1. Touch Touch Control panel Switch on the appliance until the signal sounds Acoustic signal Display/Signal Appliance switches off. Overriding the child safety device The child safety device can be released in this way for a single cooking session; it remains activated afterwards. Touch Control panel Switch on the appliance and at the same time / acoustic signal Display/Signal Until the appliance is next switched off, it can used as normal. 14 electrolux operating the appliance Using the timer All cooking zones can use each use one of the two timer functions at the same time. Function Automatic cut-out Condition a heat setting is set Outcome after the time has elapsed acoustic signal 00 flashes Cooking zone switches off acoustic signal 00 flashes Countdown timer cooking zones not in use If a cooking zone is switched off, the timer function set is also switched off. If a heat setting is set on this cooking zone in addition to a countdown timer, the cooking zone is switched off after the time set has elapsed. operating the appliance electrolux 15 Selecting the cooking zone Step 1. Control panel Touch Touch 1x 1x Display Pilot light for the back cooking zone flashes Pilot light for the front cooking zone flashes The heat setting indicator of the selected cooking zone goes out, as long as the timer time can be set. If the pilot light is flashing more slowly, the heat setting indicator appears again and the heat setting can be re-set or modified. If other timer functions are set, after a few seconds the shortest remaining time of all the timer functions is displayed and the corresponding pilot light flashes. 16 electrolux operating the appliance Setting the time Step 1. Control panel field Display Select cooking zone Pilot light of the cooking zone selected flashes Touch or for the cooking zone selected 00 to 99 minutes After a few seconds the pilot light flashes more slowly. Switching off the Timer function Step 1. Control panel Select a cooking zone Display Pilot light of the selected cooking zone flashes more quickly. Remaining time is displayed 2. Touch for the cooking The remaining time counts down to 00. Cleaning the appliance after each use 1. Wipe the appliance with a damp cloth and a little washing up liquid. Rub the appliance dry using a clean cloth. cleaning and care electrolux 23 Removing deposits 1. Place a scraper on the glass ceramic surface at an angle. Remove residues by sliding the blade over the surface. Wipe the appliance with a damp cloth and a little washing up liquid. Rub the appliance dry using a clean cloth. Remove Type of dirt sugar, food containing sugar plastics, tin foil limescale and water rings fat splashes shiny metallic discolouration immediately yes yes ------- when the appliance has cooled down ----yes yes yes using a scraper* cleaner for glass ceramic or stainless steel* *Scrapers and cleaners for glass ceramic and stainless steel can be purchased in specialist shops Remove stubborn residues with a cleaner for glass ceramic or stainless steel. Scratches or dark stains on the glass ceramic that cannot be removed do not however affect the functioning of the appliance. 24 electrolux what to do if . . . What to do if . . . Problem The cooking zones will not switch on or are not functioning Possible cause More than 10 seconds have passed since the appliance was switched on The child safety device is switched on Several sensor fields were touched at the same time Safety cut-out has been triggered Remedy Switch the appliance on again. Deactivate the child safety device (See the section "Child safety device") Only touch one sensor field Remove any objects (pan, cloths, etc. ) that are lying on the control panel. Switch the appliance on again The residual heat indicator is not displaying anything Power function cannot be switched on The cooking zone was only on If the cooking zone is supfor a short time and is therefore posed to be hot, call the Cusnot hot tomer Service Department. The Power function function Let cooking surface cool down. has already been activated several times quickly one after the other Display changes between two Power Management is reduc- See section "Power Manageheat settings ing the power of this cooking ment" in the Operating the Apzone pliance chapter lights up Unsuitable cookware No cookware on the cooking zone Use suitable cookware Place cookware on the cooking zone The diameter of the bottom of Move onto a smaller cooking the cookware is too small for zone the cooking zone Use suitable cookware and number are displayed Electronics fault Disconnect the appliance from the electrical supply for a few minutes (Take the fuse out of the house's wiring system) If after switching on again, is displayed again, call the customer service department what to do if . . . [. . . ] ­ For the four corners of the rabbet the ends of the sealing tapes must be cut into mitres. ­ Stick the sealing tape flush into the corner of the rabbet, so that no silicon compound can get under the glass ceramic when grouting. ­ Don't stretch the tapes when sticking them on. · If installing flush with the work surface, use the sealing tape with dimensions 10x3mm. [. . . ]