User manual AEG-ELECTROLUX HC5690-M

[. . . ] 65 Extractor version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Filter Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Control Panel DK 9160 - DK 9190 - DK 9360 - DK 9390 - HC 3360 . . . . . . . . . . . . . . . . . . . . . . . . . 66 Control Panel DK 9660 - DK 9690 - HC 5690 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The control switches are located on the units front panel: AOFF ON push button Press once or more to obtain the function desired: ON: the hood switches on to the last speed selected. OFF: all the functions are switched off except the illumination. Speed selection push button (extraction power). Press this push button once or more to select the most suitable extraction speed (power) (1-2-3). The display shows the extraction power selected, signalling the saturation of the filters (F). The Intensive speed runs for 5 minutes: If the hood is on when the Intensive speed is activated, the hood reverts to previous speed after 5 minutes. If the hood is off when the Intensive speed is activated, the hood will be turned off after 5 minutes. To interrupt the Intensive speed, press button A or B. Light ON/OFF BCD- H- i A B C D E Should the hood or the controls fail to operate: disconnect the power supply for at least 5 seconds, then turn the hood back on again. 67 Control Panel DK 9960 - DK 9990 Best results are obtained by using a low speed for normal conditions and a high speed when odours are more concentrated. Turn the hood on a few minutes before you start cooking, you will then get an under pressure in the kitchen. The hood should be left on after cooking for about 15 minutes or until all the odours have disappeared. If the hood is to be used with a charcoal filter, the saturation indicator light must be enabled as follows: Pressing keys B and D simultaneously for three seconds, LED F lights up and begins to flash the 1st speed led. After 1 second the 2nd speed led also flashes and the system emits a sound signal (-Beep-) to indicate setting taking place. To remove the charcoal filter signal press push buttons B and D simultaneously for 3 seconds. LED F lights up and begins to flash the 1st speed led (grease filter) and the 2nd speed led. After 1 second, only the 1st speed led continues to flash. The system emits a sound signal (-Beep-) to indicate setting taking place. Grease filter LED The 1st speed led (+ led F) flashes, when it is time to clean the grease filter. Always comply with the maintenance instructions for the grease filter. Charcoal filter LED The 2nd speed led (+ led F) flashes, when the charcoal filter needs to be cleaned or replaced. Resetting the saturation indicator After cleaning or replacing the filters, press button 1 for 3 seconds until the 1st speed led or the second speed led stops flashing. At normal use the filter should be cleaned every second month (when using the hood 2, 5 hours per day, in avarage). [. . . ] as the engineer will make a charge if the fault is not a mechanical or electrical breakdown even the appliance is under warranty. Please note that proof of purchase is required for in-guarantee service calls. Help us to help you Please determine your type of enquiry before writing or telephoning. When you contact us we need to know: Your name Address and post code Telephone number Clear and concise details of the fault Name and model of the appliance* E number* * This information can be found on the rating plate, which can be seen when the grease filters are removed. [. . . ]