User manual AEG-ELECTROLUX HD6470-M-GB

[. . . ] DM 8700 - DM 8600 DM 8400 - DD 8770 HD 6470 Dunstabzugshaube Afzuigkap Hotte aspirante Cooker Hood Montage- und Gebrauchsanweisung Installatie- en gebruiksaanwijzing Notice dutilisation et dinstallation Operating and Installation Instructions Contents Safety warnings For the user For the installer Description of the Appliance Extraction Recirculation Control Panel - Model DM 8700 - DD 8770 Switching on the hood Switching on the light Control device for grease or charcoal filter Led signal for grease filter Led signal for charcoal filter Re-setting the saturation signal Control Panel - Model DM 8600 Control device for grease and charcoal filters Grease filter LED (D) Charcoal filter LED (E) Resetting the saturation indicator Control Panel - Model DM 8400 - HD 6470 Maintenance and care Cleaning the hood Metal grease filter Removing the metal grease filter Charcoal filter Changing the light bulb Special accessories What to do if Technical assistance service Technical Specifications Mounting accessories included Electrical connection Safety warnings for the electrician Wall unit mounting Special accessories/Vapour screen Printed on recycled paper AEG - putting words into action 64 65 65 65 67 67 67 68 69 69 69 69 69 69 70 71 71 71 71 72 73 73 73 73 74 75 77 76 77 78 78 79 79 80 83 Safety warnings For the user The cooker hood is designed to extract unpleasant odours from the kitchen, it will not extract steam. Always cover lighted elements, to prevent excess heat from damaging the appliance. In the case of oil, gas and coal fired cookers it is essential to avoid open flames. Also, when frying, keep the deep frying pan on the cooker top/cooker under careful control. [. . . ] If the hood is off when the Intensive speed is activated, the hood will be turned off after 5 minutes. To interrupt the Intensive speed, press button A or B. Light OFF Light ON FG- HI- A B CDE F G H I Should the hood or the controls fail to operate: disconnect the power supply for at least 5 seconds, then turn the hood back on again. 70 Control device for grease and charcoal filters This hood is fitted with a device that signals when it is necessary to clean the grease filter or the charcoal filter (in the case of recirculation version with charcoal filter). On delivery, the hood is not supplied with an charcoal filter, so the saturation indicator will be disabled. If the hood is to be used with a charcoal filter, the saturation indicator light must be enabled as follows: Press buttons B and G simultaneously and hold them for 3 seconds. At first only the grease filter LED D will light up, but when the charcoal filter LED E lights up the saturation indicator will be enabled. To disable it: Press buttons B and G again simultaneously and hold them for 3 seconds, until the charcoal filter LED goes out. Grease filter LED (D) LED D will start to flash when it is time to clean the grease filter. Cleaning will be necessary after 40 working hours. Always comply with the maintenance instructions for the grease filter. Charcoal filter LED (E) The charcoal filter LED E will start to flash when the charcoal filter needs to be replaced. This operation is necessary after approximately 160 working hours. Resetting the saturation indicator After cleaning or replacing the filters, press button A for 3 seconds until the grease filter LED D or the charcoal filter LED E stops flashing. 71 Control Panel Model DM 8400 - HD 6470 Best results are obtained by using a low speed for normal conditions and a high speed when odours are more concentrated. Turn the hood on a few minutes before you start cooking, you will then get an under pressure in the kitchen. The hood should be left on after cooking for about 15 minutes or until all the odours have disappeared. To do this you will need an original AEG charcoal filter (available from your local Service Force Centre). Cleaning/replacing the charcoal filter Unlike other charcoal filters, the LONGLIFE charcoal filter can be cleaned and reactivated. At normal use the filter should be cleaned every second month (when using the hood 2, 5 hours per day, in avarage). The best way to clean the filter is in the dishwasher. Use normal detergent and choose the highest temperature (65º C). Wash the filter separately so that no food parts gets stuck on the filter and later causes bad odours. To reactivate the charcoal, the filter should be dried in an oven for 10 minutes with a temperature of maximum 100º C. After approximately three years of use, the charcoal filter should be replaced with a new, as the odour reduction capacity will be reduced. Fitting Remove the frame i which supports the filter h by turning 90° the two knobs g. Insert the charcoal filter inside the frame and put all parts back in their place. [. . . ] If you decide to use the hood in exhausting version we suggest to position the upper section of the chimney so that the oulet slots are not visible once installation has ended, on the contrary if is decided to use the hood in recycling version BE SURE that the side with slots is up (see also A-BC sequence on on Fig. Assembling the chimney flue support/bracket (3 parts): The three parts should be fixed with 4 screws, the support extension is adjustable and should correspond to the internal width of the telescopic chimney flue. Assembling the deflector (3 parts only for filter version): The three parts should be fixed with 2 screws, the deflector extension is adjustable and should correspond to the width of the chimney flue support, to which it is then fixed. = B 180° X G = = X = X F A C - OK! H F G Fig. 8 Only for DD 8770 and HD 6470: Assemble the frame to the motor group (a - Fig. [. . . ]