User manual AEG-ELECTROLUX HD8694-M

[. . . ] CHDD 8694 HD 8694 Cooker Hood Operating and Installation Instructions 2 Contents Safety warnings For the user For the installer Description of the Appliance Extractor version Filter Version Hood Operation Using the Remote Control Setting the Remote Control Remote Control Maintenance Maintenance and care Metal grease filter Open the metal grease filter Charcoal filter Changing the light bulb Special accessories What to do if Service and spare parts Guarantee Conditions Technical Details Mounting accessories included Electrical connection Safety warnings for the electrician Wall unit mounting 4 4 4 6 6 7 8 9 9 9 10 10 11 12 13 13 14 15 16 17 17 17 17 18 3 Safety warnings For the user The cooker hood is designed to extract unpleasant odours from the kitchen, it will not extract steam. Always cover lighted elements, to prevent excess heat from damaging the appliance. In the case of oil, gas and coal fired cookers it is essential to avoid open flames. Also, when frying, keep the deep frying pan on the cooker top/ cooker under careful control. [. . . ] 9 Battery compartment cover Maintenance and care The hood must always be disconnected from the electricity supply before beginning any maintenance work. Never insert pointed objects in the motors protective grid. Wash the outside surfaces using a delicate detergent solution. Never use caustic detergents or abrasive brushes or powders. Only ever clean the switch panel and filter grille using a damp cloth and delicate detergents. It is extremely important to clean the unit and change the filters at the recommended intervals. Failure to do so will cause grease deposits to build up that could constitute a fire hazard. Metal grease filter The purpose of the grease filters is to aspirate grease particles which form during cooking and it must always be used, either in the external evacuation or internal recycling function. Attention: the metal grease filters must be removed and washed, either by hand or in the dishwasher, every four weeks. 10 Open the metal grease filter First, push both metal grease filter handles towards the centre, then extract the filter M, pulling downwards. Repeat the steps with the second filter. Hand washing Soak grease filters for about one hour in hot water with a greaseloosening cleaner, then rinse off thoroughly with hot water. Refit the grease filters when they are dry. Dishwasher Place grease filters in the dishwasher. Select most powerful washing programme and highest temperature, at least 65°C. Refit the grease filters when they are dry. When washing the metal grease filter in the dishwasher a slight discolouration of the filter can occur, this does not have any impact on its performance. Clean the inner housing using a hot detergent solution only (never use caustic detergents, abrasive powders or brushes). Fig. 4 11 Charcoal filter The charcoal filter is already supplied and mounted in place. The charcoal filter should only be used if you want to use the hood in its filtering function. The charcoal filters absorb smells and odours. The charcoal filter cannot be washed nor regenerated. The charcoal filter should be replaced every 6 months under normal use. Replacement filters are available from your local Service Force Centre. [. . . ] Before you move please contact your nearest Customer Care Centre, listed below, to give them details of your new home. They will then ensure that the local Service Organisation is aware of your move and able to look after you and your appliances. France Germany Italy Sweden UK 16 Senlis Nürnberg Pordenone Stockholm Slough +33 (0) 44 62 29 29 +49 (0) 911 323 2600 +39 (0) 1678 47053 +46 (0) 8 738 7910 +44 (0) 1753 219899 Guarantee conditions Technical Details Dimensions - extractor version (in cm): Height - Width - Depth 78, 5/120 - 89, 8 - 50, 5 Maximum absorbed power: 340 W Motor absorption: 1 x 300 W Lighting: 2 x 20W Length of the cable: 120 cm Mounting accessories included 1 deflector 1 chimney support 1 reduction flange Ø 125-120 mm 1 remote control 1 charcoal filter (already fitted) 1 support bracket 8 wood-screws 5 x 45 mm (for wall mounting - 2 as spare parts) 8 wall plugs Ø 8 mm (for wall mounting - 2 as spare parts) 6 washers (2 for chimney supprot - 2 for lower fixing - 2 as spare parts) 6 metal screws 3, 5 x 9, 5 (for chimney, deflector and connection flange - 2 as spare parts) 2 metal screws 3, 5 x 6, 5 (for connection block and circuit board support). We reserve the right to change specifications and colours as a result of our policy of continuing technological development. Electrical connection Safety warnings for the electrician The electric outlet should be placed on the wall inside the chimney. The hood has a power cable, 150 cm, with earth connection and the rated voltage is 220 - 240 V. [. . . ]