User manual AEG-ELECTROLUX JLBIHD608

[. . . ] JLBIHD608 built-in cooker hood Instruction manual Important Safety Information It is most important that this instruction manual should be retained with the appliance for future reference. Should the appliance be sold or transferred to another owner, or should you move house and leave the appliance, always ensure that the book is supplied with the appliance in order that the new owner can get to know the functioning of the appliance and the relevant warnings. These warnings ha ve been pr ovided in the inter est of saf ety . You MUST read them carefully before use or installation by a qualified person. If you are unsure of the meanings of these warnings contact the John Lewis branch from which you purchased the appliance. Installation · Any installation work must be undertaken by a qualified and competent person to the relevant National Standards. [. . . ] IMPORTANT: Before installation check that the wall to which the cooker hood is to be fitted for electric cables, water pipes and gas. · If it is necessary to fix the cooker hood to a hollow construction plaster or patition board structure then it must be sufficiently reinforced to be quite rigid in the area for the cooker hood mounting brackets. · The cooker hood must be fitted using the special brackets supplied or it will not be possible to adjust the alignment and depth of the cooker hood once it has been fixed. Use the paper template provided to mark the hole positions on the wall for the mounting bracket fixing screws. Check the hole distances are correct with a tape measure as stated on the template. IMPORTANT: At this stage allow 25 mm clear space above the cooker hood (if it is to be fitted under a wall cabinet or similar) to enable it to be hooked on and off the brackets for subsequent removal for decorating or service. · When drilling the holes for the wall fixing brackets care must be taken to ensure that they are quite level as there is minimal height adjustment of the fixing brackets. The brackets should be fitted with the round end at the bottom using the plastic rawl plugs and screws provided. · If the brackets are to be fitted to a hollow plaster or partition board structure then the plastic rawl plugs provided must not be used. (Special rawl plugs are available for hollow plaster or partition board walls). · Once the brackets are secured lift the hood squarely to the wall slightly higher than the brackets and lower the cooker hood until the cooker hood locates onto the two brackets. Ensure that the cooker hood is correctly located before letting go. 7 Fitting the Decor Panel The dimensions of the decor panel to be fitted should be (W) 59. 6 cm x (H) 45 cm. To fit the decor panel onto the cooker hood: · Remove the visor from the cooker hood. · Place the decor panel face down. · Ensure the template is aligned with the top edge of the decor panel. · Using the template mark the hole positions for the fixing screws on the reverse side of the decor panel. · Place the visor face down on the reverse side of the decor panel and align the top edge of the visor with the decor panel to check the screw holes aligh correctly. · Pilot drill the holes and secure using the 8 No Ø3. 9 x 13 mm countersunk flat headed screws supplied. Should a decor panel be fitted with a height exceeding 45 cm, failure to align the top edge of the template with the top edge of the visor will prevent the visor from opening correctly when installed. Adusting the Hanging Brackets The cooker hood can be adjusted in depth from 27 to 36 cm, which makes the cooker hood suitable for installation with most makes of UK and European kitchen cabinets. To adust the depth of the cooker hood: · Loosen the screws (C) at the front of each extension arm as illustrated. · When the screws are loose align the front of the hood with the front of the adjoining wall cabinet. · Turn the screws (B) at the rear of each bracket (clockwise to lower the hood or anti-clockwise to raise the hood) to ensure perfect alignment with the wall cabinet as illustrated. [. . . ] Allow to dry completely before replacing. 12 Before carrying out any maintenance or cleaning isolate the cooker hood from the mains supply. Charcoal Filters In the recirculation mode the charcoal filters absorb smells and unwanted odours. The charcoal filters cannot be cleaned, we recommend they should be replaced approximately every three months or more often if the hood is used for more than three hours per day. A To Remove/Replace the Charcoal Filters The charcoal filter is fitted to the motor support behind the grease filter on the inside the cooker hood as illustrated. · Place one hand over the filter (B) and twist the disk (C) in the centre anticlockwise as indicated to open. · Take down the filter taking care not to damage the paper and expose the contaminated charcoal, which would cause serious damage to clothing or the surrounding decorations. [. . . ]