User manual AEG-ELECTROLUX L10500V

[. . . ] LAVAMAT 10500 VI LAVAMAT 14500 VI Washing Machine Instruction Booklet LAVAMAT ON / OFF 1400 900 700 500 NO SPIN SPIN SPEED PREWASH STAIN QUICK RINSE HOLD EXTRA RINSE DELAY START START PAUSE WASH TIME PREWASH WASH RINSES RINSE HOLD DRAIN SPIN CLEAN FILTER END RESET MINIPROGRAMME SPIN DRAIN SOFTENERS RINSES SOAK COLD COTTON 95 E 60 50 40 30 COLD WOOLLENS 40 30 60 30 40 COLD 40 40 50 EASYCARES EASY TO IRON DELICATES PERFEKT IN FORM UND FUNKTION Dear customer, Please read these operating instructions carefully and pay particular attention to the safety notes indicated in the first pages. We recommend that you keep this instruction booklet for future reference and pass it on to any future owners. The warning triangle and/or the key words (Warning!, Caution!) emphasize information that is particularly important for your safety or correct functioning of the appliance. This symbol guides you, step by step, in the operation of the appliance. [. . . ] * The consumption data shown on this chart is to be used as a guide only, as it may vary depending on the quantity and type of laundry, on the inlet water temperature and on the ambient temperature. It refers to the highest temperature for each wash programme. 26 Programme chart Special programmes Programme Type of laundry Programme phases Soak at 30°C. The machine automatically empties itself after 18 hours. EXTRA RINSE RINSE HOLD SPIN SPEED RINSE HOLD SPIN SPEED Consumption* Additional Max. Energy Water Duration functions load kWh lt. min. Soak Heavily soiled fabrics, except wool. 4. 5 kg 0. 25 19 20 Rinses This programme can 3 rinses with liquid be used for additive. washed garments. 4. 5 kg 0. 12 30 48 Hand washed gar- 1 rinse with liquid Softeners ments to be additive. For emptying out the last rinse water in The water is empprogrammes tied out. (700 rpm max) For cancelling the wash programme which is running. 4. 5 kg / 15 21 Drain / / / 3 Spin 4. 5 kg RINSE HOLD SPIN SPEED / / 10 Lightly Minipro- soiled fabgramme rics except wool Reset Cancel. 2 kg 0. 25 40 30 * The consumption data shown on this chart is to be used as a guide only, as it may vary depending on the quantity and type of laundry, on the inlet water temperature and on the ambient temperature. 27 Cleaning and maintenance After each wash At the end of the wash programme, pull the dispenser drawer out a little to let it dry. Leave the door ajar to allow air to circulate. If the machine is not used for a prolonged period: Close the water tap and unplug the appliance. Maintenance Wash With the use of low temperature washes it is possible to get a build up of residues inside the drum. We recommend that a maintenance wash be performed on a regular basis. To run a maintenance wash: The drum should be empty of laundry. Select the hottest cotton wash programme. Use a normal measure of detergent, must be a powder (such as Ariel Futur). Periodical cleaning Exterior Clean the outside of the cabinet with soap and water only. Important: do not use methylated spirits, solvents or similar products to clean the cabinet. Detergent dispenser drawer After a while, detergents and fabric softeners leave deposits in the drawer. Clean the drawer, from time to time, by rinsing it under a running tap. To remove the drawer from the machine, press the button in the rear left-hand corner. 28 Cleaning and maintenance To facilitate cleaning, the top part of the additive compartment can be removed. Detergent can also accumulate inside the drawer recess: clean it with an old toothbrush. Refit the drawer after cleaning. Door seal Regularly check to see, if there are deposits or foreign objects in the rubber seal behind the door and remove them. Drain filter The drain filter collects threads and small objects inadvertently left in the laundry. Check regularly that the filter is clean. Place a container under the filter and unscrew it; some water will come out of the filter. [. . . ] The required dimensions are given in the picture C. The hinges will be fixed to the door by means of screws for wood (2-Fig. c) Mounting the door Fix the hinges (1) to the machine by means of the M5x8 screws (3-Fig. The hinges can be adjusted to compensate for possible uneven thickness of the door. [. . . ]