User manual AEG-ELECTROLUX LAV1105UD

[. . . ] This symbol guides you step by step in operating the unit. 2. . . . 3 2 After this symbol you will find detailed information on operation and practical use of the unit. The clover leaf indicates tips and information on the economical and environmentally-responsible use of the unit. This user information contains information on remedying any faults which may occur, see the section "What to do if . . . ". Printed on recycled paper. [. . . ] load1) (Dryweight)2) Type of washing, Care symbol Programme knob Temperature [in °C] P WOOL/SILK (WOLLE/SEIDE, LAINE/SOIE) COLD (KALT, FROID), 30 Possible additionalprogramme functions Wool/Silk (Handwash) 9ìï 2kg 1) The load amount inquiry operates in accordance with the EN 60456 standard load. 2) A 10 litre bucket holds around 2. 5kg of dry clothes (cotton). 3) Programme settings for testing in accordance with or in support of EN 60 456 and IEC 60 456 are described in the chapter "Consumption Values and Programme Times". 4) A temperature of at least 40°C is needed for the STAIN (Flecken, Tâches) programme, to make stain treatment products effective. 5) Only by keeping wash loads under 1kg, can creasing be largely avoided. About 1kg of dry clothes is equivalent to between 5 and 7 easy-care men's shirts. Separate Rinsing Type of washing Cottons/Linens Easy-Cares/Delicates1) 1) Reduce spin speed. load (dry weight) 5kg 2. 5kg Programme knob GENTLE RINSE (FEINSPÜLEN, RINCAGE DELICAT) Separate Spinnin Type of washing Cottons/Linens Easy-Cares1) Delicates1) Wool/Silk (Handwash)1) 1) Reduce spin speed. load (dry weight) 5kg 2. 5kg 2. 5kg 2kg SPIN (SCHLEUDERN, ESSORAGE) Programme knob 25 Instructions for use Cleaning and Care Control Panel Attention!For cleaning panels and control parts, do not use furniture polish or any aggressive cleaning agents. Wipe off control panels with a damp cloth. Use warm water to do this. 0 Washing Detergent Drawer The washing detergent drawer should be cleaned from time to time. Water tap is furred with limescale or faulty. Check the water tap and have it repaired, if necessary. 28 Instructions for use Problem Possible Cause Remedy First turn the programme selector to OFF (AUS, ARRET), then set the desired programme to the exact position. Remove the transit bolts/bars as described in the Installation and Connection instructions. Adjust the screw feet as described in the Installation and Connection instructions. The END (ENDE, FIN) indicator flashes 8 times. The programme selector has not clicked into place correctly. The transit bolt/bars were not removed. The height-adjustable screw feet have not been set correctly. The washing machine vibrates when operating or is noisy. There is very little washing in Operation is not affected by the drum (for example, only this. Water could not be drained completely before spinning, because the outlet hose has got a kink in it or the drain pump is blocked. Check the positioning of the outlet hose and even out any kinks if necessary or clean the drain pump and remove any foreign matter that might be in the pump housing. The main wash deterFollow the manufacturer's Probably too much detergent gent solution produces instructions exactly, when was used. measuring out detergent. 29 Instructions for use Problem Possible Cause The threaded inlet hose fitting is not watertight. Remedy Screw the inlet hose in firmly. The outlet hose is not water- Check the outlet hose and tight. The drain pump cover is not closed properly. [. . . ] ­ Small basins are not suitable for draining the water into them. ­ It is not permitted to submerge the end of the drainage hose into the pumped-off water. ­ When hooked into a wash-basin or a bath tub the drainage hose must be protected from slipping out of place by the supplied slip-on elbow. Otherwise the repelling power of the draining water can press the hose out of the sink. [. . . ]