User manual AEG-ELECTROLUX LAV2040GB

[. . . ] It is essential that this information is observed. This symbol guides you step by step when operating the appliance. . . . 1 3 2 This symbol gives you additional information and practical tips on using the appliance. Tips and information about the economical and environmentally friendly use of the machine are marked with the clover symbol. [. . . ] Turn the program selector clockwise to PUMP OUT, SPIN or SHORT SPIN. The water is pumped out or pumped out and the washing then spun. 22 Operating Instructions Wash Complete/Removing the Washing The washing program normally ends with the final spin. 0 After Soaking: Release the SOAKING button (the COTTONS/LINEN or EASY-CARES main wash starts). After a Rinse Hold: After a rinse hold the water must be pumped out, or the washing spun: 0 1. Either turn the program selector clockwise to SPIN or SHORT SPIN (the washing is spun according to the selected program and the spin speed set) or turn the program selector clockwise to PUMP OUT (the water is pumped out). After the program is completed: For safety reasons, the door remains locked for 1-2 minutes after the end of the program. The indicator extinguishes, the washing machine is switched off. Pull out the detergent compartment a little, so that it can dry out. Leave the main door slightly open so that the washing machine can ventilate. If the washing machine is not to be used for a long period: close the tap and isolate the washing machine from the mains. 3 23 Operating Instructions Program Tables Washing The following tables list the most commonly used and most useful programs. Washing Type, Care Symbol Max. Load (dry weight) 1) Program Selector STAIN 5kg MAIN WASH QUICK WASH Energy Saving Program Cottons ç Linen èë 5kg STAIN2) STAIN 5kg MAIN WASH QUICK WASH Easy-Cares êíî STAIN 2. 5kg 2. 5kg (or 15-20m2 net curtains) 1kg MAIN WASH QUICK WASH Delicates ì Woollens3) 9ì DELICATES COLD to 40 COLD to 40 30 to 60 EASY-CARES 30 to 60 E 70 to 95 Temperature Selector Additional Button Cottons ç WOOL 1) A 10 litre bucket contains about 2. 5kg of dry washing (cotton). 2) It is necessary to extend the time of the Energy Saving Program E (67° C) to obtain the same wash results as MAIN WASH (95° C). Filter in the threaded fitting on the water inlet hose is blocked. Close door, lock must engage audibly Open tap. Unscrew the hose from the tap, remove the Filter and clean under running water Adjust the feet according to the installation and connection instruction. Washing machine vibrates during operation or is unstable. There is only very little washing in the machine (e. g. Water cannot be completely pumped out because the drain hose is kinked or the drain pump is blocked. Check the drain hose and if necessary remove any kink or clean the drain pump and remove any foreign bodies from the pump housing. It may be necessary to reduce the amount of deterExcessive foaming dur- Probably too much detergent gent used. was used gent manufacturers recommendations. 28 Operating Instructions Malfunction Possible Cause Threaded fitting on the water inlet hose is leaking. Water runs out from under the washing machine. Fabric softener is not added, compartment À for fabric softener is filled with water. Appliance does not spin, water in the drum. Remedy Tighten the inlet hose connections. Check the inlet hose and if necessary replace it. [. . . ] Improper repairs may lead to serious risks for the user. 1 Water Connection 3 The washing machine is provided with safety devices preventing backcontamination of the water supply and complies with local water authority requirements. This appliance is designed to be permanently plumbed into your homes water supply. Before connecting up the machine to new pipework or to pipework that has not been used for some time, run off a reasonable amount of water to flush out any debris that may have collected in the pipes. 42 Installation and Connection Instructions Water Pressure The appliance is designed to operate within the following water pressure limits: minimum 1 bar (14. 5 p. i. ): Unscrew the inlet hose from the appliance at the inlet solenoid valve and remove the flow regulator (to do this, remove the sieve with needle-nose pliers and remove rubber washer behind the sieve). [. . . ]