User manual AEG-ELECTROLUX LAV770W

[. . . ] This symbol guides you step by step in operating the unit. 2. . . . 3 2 After this symbol you will find detailed information on operation and practical use of the unit. The clover leaf indicates tips and information on the economical and environmentally-responsible use of the unit. This user information contains information on remedying any faults which may occur, see the section "What to do if . . . ". [. . . ] Press the button START/PAUSE (START/PAUZE, MARCHE/PAUSE). Change the speed with the button Spin/RINSE HOLD (GEEN CENTR. , SANS ESSOR. ). Press the button START/PAUSE (START/PAUZE, MARCHE/PAUSE) again. The washing program is continued. 25 Instructions for use Washing Cycle Ended/Remove Washing After a washing program has ended, END (EINDE, FIN) lights up on the program sequence display. If you selected RINSE HOLD (GEEN CENTR. , SANS ESSOR. ), the indicator next to the button START/PAUSE (START/PAUZE, MARCHE/PAUSE) flashes. After a rinse hold, it is first necessary to pump off the water: ­ Press either the button START/PAUSE (START/PAUZE, MARCHE/ PAUSE) (water is pumped off and the washing is spun according to the program which has just run; after pressing the button START/ PAUSE (START/PAUZE, MARCHE/PAUSE) again, the spin speed can also still be changed during spinning), or ­ turn the program selector to PUMP (POMPEN, VINDAGE) and press the button START/PAUSE (START/PAUZE, MARCHE/PAUSE) (water is pumped off without spinning) or ­ turn the program selector to SPIN (CENTRIFUG. , ESSORAGE) or SHORT SPIN (KORT CENTRIFUG. , ESSOR. DELICAT) and press the button START/ PAUSE (START/PAUZE, MARCHE/PAUSE) (water is pumped off and the washing is spun or gently spun). After the end of this program step, the indicator END (EINDE, FIN) lights up. As soon as the indicator DOOR (DEUR, PORTE) lights up green, the filling door can be opened. Turn the program selector to OFF (UIT, ARRET). After washing, pull out the washing detergent drawer slightly so that it can dry out. Push on the softener insert as far as it will go so that it is secure. 30 Instructions for use 7. Use a brush to clean the entire rinsing-in part of the washing machine, especially the nozzles on the top side of the rinsing-in chamber. 8. Insert the washing detergent drawer into the guide rails and push it in. Washing Drum The washing drum is made of high-quality stainless steel. Rust deposits on the drum can occur due to foreign bodies in the washing which can cause rust. Do not clean the stainless steel drum with acidic antiliming agents, scouring agents containing chlorine or iron or steel wool. Our Customer Service Department has suitable agents available. Remove any rust deposits on the drum using a stainless steel cleaning agent. 0 Filling Door 0 Check regularly whether there are deposits or foreign bodies in the rubber sleeve behind the filling door and, if so, remove them. 31 Instructions for use What to do if . . . Remedying Faults In the event of a fault, try to solve the problem yourself with the aid of the information provided here. If you call Customer Service to deal with one of the faults listed here or to remedy an operating fault, the customer service technician's visit will not be free of charge, even during the warranty period. · If the fault code E10, E20 or E40 is shown in the multidisplay, you may be able to remedy the fault yourself (see Faults Table below). After remedying the fault, press the button START/PAUSE (START/ PAUZE, MARCHE/PAUSE). If the fault code is shown again, inform Customer Service. [. . . ] It is absolutely essential to install the drainage hose free of pinches. Water Drainage into a Siphon The grommet on the end of the hose fits all commonly used siphon types. Secure the grommet/siphon connecting point with a hose clamp. 0 Draining the water into a basin Attention!­ Small basins are not suitable for draining the water into them. [. . . ]