User manual AEG-ELECTROLUX LAVAMAT 1571 TURBO SEN

[. . . ] It is essential that this information is observed. This symbol guides you step by step when operating the appliance. . . . 1 3 2 This symbol gives you additional information and practical tips on using the appliance. Tips and information about the economical and environmentally friendly use of the machine are marked with the clover symbol. [. . . ] It is normal for the rotation speed of the program selector to vary during the program. Changing settings: During the washing program you can: Change the spin speed Select o (RINSE HOLD) Change the temperature setting Other settings cannot be altered. Turn the program selector clockwise to v (PUMP OUT), position 6 (SPIN), or position 8 or 11 (SHORT SPIN). The water is pumped out or pumped out and the washing then spun. 21 Operating Instructions Washing Cycle Complete/Removing the Washing The washing program normally ends with the final spin. After a rinse hold: After a rinse hold the water must first be pumped out or the washing spun: 0 1. Either turn the program selector clockwise to position 6 (SPIN), or position 8 or 11 (SHORT SPIN) (the washing is spun according to the selected program and the spin speed set) or turn the program selector clockwise to v (PUMP OUT) (the water is pumped out). Once the program is finished: For safety reasons, the door remains locked for 1-2 minutes after the end of the program. The indicator extinguishes, the washing machine is switched off. Pull out the detergent dispenser drawer a little so that it can dry out. This helps to prevent stagnant smells and helps to preserve the door seal. 3 Important!If the washing machine is not to be used for a long period: close the water tap and isolate the washing machine from the mains. 22 Operating Instructions Program Tables Washing The following tables list the most commonly used and most useful programs. Type of Washing, Care Symbol Cottons Energy Saving Program Cottons Linen Max. 25 Operating Instructions What to do when 3 The whistling noise when spinning may be different to your prevous washing machine which is due to the modern drive system. Trouble Shooting If you call out an engineer and the fault is listed here, a charge is levied even if the appliance is in guarantee. Malfunction Possible Cause Remedy Washing machine does Mains plug is not plugged in. Filter in the threaded fitting on the water inlet hose is blocked. Close door, lock must engage audibly Open water tap. Unscrew the hose from the tap, remove the Filter and clean under running water Adjust the feet according to the installation and connection instruction. Washing machine vibrates during operation or is unstable. There is only very little washing in the machine (e. g. Water cannot be completely pumped out because the drain hose is kinked or the drain pump is blocked. Check the drain hose and if necessary remove any kink or clean the drain pump and remove any foreign bodies from the pump housing. It may be necessary to reduce the amount of deterExcessive foaming dur- Probably too much detergent gent used. was used gent manufacturers recommendations. 26 Operating Instructions Malfunction Possible Cause Threaded fitting on the water inlet hose is leaking. Water runs out from under the washing machine. Fabric softener is not added, compartment for fabric softener is filled with water. Appliance does not spin, water in the drum. Remedy Tighten the inlet hose connections. [. . . ] This appliance is designed to be permanently plumbed into your homes water supply. Before connecting up the machine to new pipework or to pipework that has not been used for some time, run off a reasonable amount of water to flush out any debris that may have collected in the pipes. Water Pressure The appliance is designed to operate within the following water pressure limits: minimum 1 bar (14. 5 p. i. ): Unscrew the inlet hose from the appliance at the inlet solenoid valve and remove the flow regulator (to do this, remove the sieve with needle-nose pliers and remove rubber washer behind the sieve). Retain the washer for future use. 42 Installation and Connection Instructions Inlet Hose Connection The inlet hose provided is 1. 2 or 1. 3 metres depending on the model. [. . . ]